Download or read book An Investigation of Gas Bubble Injection from Single Nozzles Into Water and Liquid Metal Pools written by Devin W. Gray and published by . This book was released on 2008 with total page 258 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental and numerical studies on liquid metal cooled fast reactors written by Songbai Cheng and published by Frontiers Media SA. This book was released on 2023-03-03 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Light Metals 2016 written by Edward Williams and published by Springer. This book was released on 2016-12-20 with total page 983 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Light Metals symposia are a key part of the TMS Annual Meeting & Exhibition, presenting the most recent developments, discoveries, and practices in primary aluminum science and technology. Publishing the proceedings from these important symposia, the Light Metals volume has become the definitive reference in the field of aluminum production and related light metal technologies. The 2016 collection includes papers from the following symposia: 1.Alumina and Bauxite 2.Aluminum Alloys, Processing, and Characterization 3.Aluminum Reduction Technology 4.Cast Shop Technology 5.Electrode Technology 6.Strip Casting
Download or read book An Investigation of Gas Bubble Generation and Detection in Water and Mercury written by Stuart Alexander Walker and published by . This book was released on 2010 with total page 109 pages. Available in PDF, EPUB and Kindle. Book excerpt: The pressure increase attributed to the energy deposition in the liquid metal target of the Spallation Neutron Source results in cavitation and pitting erosion of the target pressure boundary. Introducing compressibility in the form of small gas bubbles will extend the lifetime of the target vessel. The pressure rise caused by the beam energy deposition occurs in one microsecond, which encourages use of bubbles of radius less than 20 microns, such that the bubble response to pressure change is adequately fast. Gas volume fraction near 0.5% is sufficient to accommodate the mercury volumetric expansion and reduce the pressure rise. Bubble production and detection technologies are developed herein to allow control of the bubble diameter and volume fraction in an opaque liquid metal. This research infers bubble size in the form of a probability density function using dynamic gas delivery pressure and mass flow, and passive acoustic emissions at bubble birth, for a single orifice bubbler. Terminal rise velocities are also measured and used to infer bubble diameter. The gas volume fraction is inferred from the acoustic sound speed using the so-called low frequency Wood's Limit model for sound speed in a bubbly media.
Download or read book Liquid liquid Mixing by Gas Injection in a Pool Configuration written by Faustino Gonzalez Gomez and published by . This book was released on 1987 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Theoretical Investigation of Gas Bubble Liquid Mixture Flows Through Converging Diverging Nozzles written by Subba Rao Gutti and published by . This book was released on 1972 with total page 67 pages. Available in PDF, EPUB and Kindle. Book excerpt: Solutions are developed for a one dimensional compressible gas bubble-liquid mixture flow through a converging-diverging nozzle. Gas is assumed in the form of spherical bubbles that do not exchange mass with the liquid, but allowance is made for a differential between bubble and liquid velocities. The critical condition for the specified initial flow conditions is found by iteration to establish the local slope of the nozzle wall at each step near the throat, and thus the critical throat is designed uniquely for each flow. Assuming adiabatic expansion for the air bubbles critical and supercritical solutions are obtained for a few specified initial conditions. A choking condition is noted at the section just upstream of the geometric throat of the nozzle. (Author).
Download or read book Light Metals 2016 written by The Minerals, Metals & Materials Society (TMS) and published by John Wiley & Sons. This book was released on 2016-02-09 with total page 1083 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 2016 collection will include papers from the following symposia: Alumina and Bauxite Aluminum Alloys, Processing, and Characterization Aluminum Reduction Technology Cast Shop Technology Electrode Technology Strip Casting
Download or read book Modeling Multiphase Materials Processes written by Manabu Iguchi and published by Springer Science & Business Media. This book was released on 2010-11-10 with total page 416 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modeling Multiphase Materials Processes: Gas-Liquid Systems describes the methodology and application of physical and mathematical modeling to multi-phase flow phenomena in materials processing. The book focuses on systems involving gas-liquid interaction, the most prevalent in current metallurgical processes. The performance characteristics of these processes are largely dependent on transport phenomena. This volume covers the inherent characteristics that complicate the modeling of transport phenomena in such systems, including complex multiphase structure, intense turbulence, opacity of fluid, high temperature, coupled heat and mass transfer, chemical reactions in some cases, and poor wettability of the reactor walls. Also discussed are: solutions based on experimental and numerical modeling of bubbling jet systems, recent advances in the modeling of nanoscale multi-phase phenomena and multiphase flows in micro-scale and nano-scale channels and reactors. Modeling Multiphase Materials Processes: Gas-Liquid Systems will prove a valuable reference for researchers and engineers working in mathematical modeling and materials processing.
Download or read book A Parametric Investigation of Gas Bubble Growth and Pinch off Dynamics from Capillary tube Orifices in Liquid Pools written by Deepak Saagar Kalaikadal and published by . This book was released on 2012 with total page 125 pages. Available in PDF, EPUB and Kindle. Book excerpt: The air-bubble dynamics phenomena in adiabatic liquid pools has been studied so as to present a better understanding of the parameters which that govern the process of ebullience, bubble growth and departure from a submerged capillary-tube orifice. The orifice diameter is found to directly dictate the bubble departure diameter, and the pinch-off is controlled by a characteristic neck-length. To study the role of orifice size on the growth and departure of adiabatic single bubbles, experiments were performed with different diameter capillary tubes submerged in of distilled de-ionized water as well as some other viscous liquids. A correlation has been developed based on the experimental data of this study along with those reported by several others in the literature. The predictions of this correlation agree very well with measured data for water as well as several other more viscous liquids. It is also found that the bubble departure diameter is the same as the orifice diameter when the latter equals twice the capillary length. The phenomenon of bubble necking and departure was explored experimentally and through a scaling analysis. Experiments were performed with five different liquids (water, ethanol, ethylene glycol, propylene glycol, and glycerol) to extract the departure neck-lengths for isolated gas bubbles at pinch-off from the capillary orifice. A scaling analysis of the experimental data indicated that the bubble neck-length at departure or pinch-off was predicted by a balance of buoyancy, viscous and surface tension forces. These were established to be represented by the Galilei and Morton numbers, and a power-law type predictive correlation has been shown to be in excellent agreement with the available data over a wide range of liquid properties. To characterize and model the growth and departure of single bubbles in different liquid pools, a theoretical model has been established. The motion of the gas-liquid interface has been modeled as a scaled force balance involving buoyancy, gas-momentum, pressure, surface tension, inertia and drag. With one-dimensional scaling of these forces, the model captures the incipience, growth, necking and departure of a bubble as it emerges from the orifice. Here necking and pinch-off is modeled based on the newly developed neck-length correlation. The results are compared with experimental data and are found to be in excellent agreement for a range of liquids, orifice sizes and flow rates. The predictions highlight the variations in bubble equivalent diameters at departure with orifice sizes, flow rates and fluid properties, and they further reiterate the well-established two-regime theory of bubble growth. The latter involves (a) the constant volume regime, where the bubble volume remains near constant and relatively independent of flow rate, and (b) the growing bubble regime, where the size of the bubble increases proportionately with the gas flow rate. Finally, the complex nature of ebullience in aqueous surfactant solutions has been studied using the reagents FS-50, SDS, and CTAB. The influence of the modulated liquid surface tension or more specifically, the role of the time dependent dynamic surface tension on the formation and departure of adiabatic bubbles has been investigated. Comparative studies have been undertaken to investigate the effect of time-dependent surface tension relaxation in surfactant solutions as opposed to ebullience in pure liquids with the same equilibrium surface tensions. Results highlight the effects of the surfactant's molecular weight on the adsorption-desorption kinetics, and the consequent influence on ebullience. It has been established that the bubbling characteristics in surfactant solutions are, in the first order, governed by the dynamic surface tension of the solute-solvent system.
Download or read book Bubble Generation in a Continuous Liquid Flow Under Reduced Gravity Conditions written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-13 with total page 158 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present work reports a study of bubble generation under reduced gravity conditions for both co-flow and cross-flow configurations. Experiments were performed aboard the DC-9 Reduced Gravity Aircraft at NASA Glenn Research Center, using an air-water system. Three different flow tube diameters were used: 1.27, 1.9, and 2.54 cm. Two different ratios of air injection nozzle to tube diameters were considered: 0.1 and 0.2. Gas and liquid volumetric flow rates were varied from 10 to 200 ml/s. It was experimentally observed that with increasing superficial liquid velocity, the bubbles generated decreased in size. The bubble diameter was shown to increase with increasing air injection nozzle diameters. As the tube diameter was increased, the size of the detached bubbles increased. Likewise, as the superficial liquid velocity was increased, the frequency of bubble formation increased and thus the time to detach forming bubbles decreased. Independent of the flow configuration (for either single nozzle or multiple nozzle gas injection), void fraction and hence flow regime transition can be controlled in a somewhat precise manner by solely varying the gas and liquid volumetric flow rates. On the other hand, it is observed that uniformity of bubble size can be controlled more accurately by using single nozzle gas injection than by using multiple port injection, since this latter system gives rise to unpredictable coalescence of adjacent bubbles. A theoretical model, based on an overall force balance, is employed to study single bubble generation in the dynamic and bubbly flow regime. Under conditions of reduced gravity, the gas momentum flux enhances bubble detachment; however, the surface tension forces at the nozzle tip inhibits bubble detachment. Liquid drag and inertia can act either as attaching or detaching force, depending on the relative velocity of the bubble with respect to the surrounding liquid. Predictions of the theoretical model compare well with performed expe
Download or read book Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics written by and published by . This book was released on 2006 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt: Session 1 : review of the state of art of present CDF codes -- Session 2 : review of current and planned experimental HLM programs -- Session 3 : elaboration of future activities.
Download or read book Metals Abstracts written by and published by . This book was released on 1999-04 with total page 972 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Energy Research Abstracts written by and published by . This book was released on 1983 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ISIJ International written by and published by . This book was released on 1998 with total page 818 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book CIM Bulletin written by Canadian Institute of Mining and Metallurgy and published by . This book was released on 1981 with total page 974 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1974 with total page 992 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1976-05 with total page 912 pages. Available in PDF, EPUB and Kindle. Book excerpt:
