Download or read book An Integrated Lossless and Accurate Current sensing Technique for High performance Switching Regulators written by H. Pooya Forghani-zadeh and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Switching power converters are an indispensable part of every battery-operated consumer electronic product, nourishing regulated voltages to various subsystems. In these circuits, sensing the inductor current is not only necessary for protection and control but also is critical to be done in a lossless and accurate fashion for state-of-the-art advanced control techniques, which are devised to optimize transient response, increase the efficiency over a wide range of loads, eliminate off-chip compensation networks, and integrate the power inductor. However, unavailability of a universal, integrable, lossless, and accurate current-sensing technique impedes the realization of those advanced techniques and limit their applications. Unfortunately, use of a conventional series sense resistor is not recommended in high-performance, high-power switching regulators where more than 90% efficiency is required because of their high current levels. A handful of lossless current-sensing techniques are available but their accuracies are significantly lower than the traditional sense resistor scheme. Among available lossless but not accurate techniques, an off-chip, filter-based method that uses a tuned filter across the inductor to estimate current flow and its accuracy is dependent on the inductance and its equivalent series resistance (ESR) was selected for improvement because of its inherent continuous and low-noise operation. A schemes is proposed to adapt the filter technique for integration by automatically adjusting bandwidth and gain of an on-chip programmable gm-C filter to the off-chip power inductor during the system start-up through measuring the inductance and its ESR with on-chip generated test currents. The IC prototype in AMI2s 0.5-um CMOS process achieved overall DC and AC gain errors of 8% and 9%, respectively, at 0.8 A DC load and 0.2 A ripple currents for inductors from 4 uH-14 uH and ESR from 48 mOhm to 384 mOhm when lossless, state-of-the-art schemes achieve 20640% error and only when the nominal specifications of power component (power MOSFET or inductor) are known. Moreover, the proposed circuit improved the efficiency of a test bed current-mode controlled switching regulator by more than 2.6% at 0.8 A load compared to the traditional sense resistor technique with a 50 mOhm sense resistor.
Download or read book Current Sensing Techniques and Biasing Methods for Smart Power Drivers written by Sri Navaneethakrishnan Easwaran and published by Springer. This book was released on 2017-12-28 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a detailed description of fault tolerant design techniques for smart power drivers and their application in the design of automotive airbag ICs to ensure correct deployment. The book begins with an introduction to the nature of electrical loads in the car, then moves on to describe various current sensing circuits, featuring thermal simulations. It shows how simple design techniques can be applied to ensure appropriate functionality of the IC under any power up condition. It concludes by introducing diagnostic circuits and measurement results. This book is a useful reference for automotive IC designers and provides specifications and design guidelines not found in the current literature.
Download or read book New Current Sensing Solutions for Low cost High power density Digitally Controlled Power Converters written by Silvio Ziegler and published by . This book was released on 2009 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt: [Truncated abstract] This thesis studies current sensing techniques that are designed to meet the requirements for the next generation of power converters. Power converters are often standardised, so that they can be replaced with a model from another manufacturer without an expensive system redesign. For this reason, the power converter market is highly competitive and relies on cutting-edge technology, which increases power conversion efficiency and power density. High power density and conversion efficiency reduce the system cost, and thus make the power converter more attractive to the customer. Current sensing is a vital task in power converters, where the current information is required for monitoring and control purposes. In order to achieve the above-mentioned goals, existing current sensing techniques have to be improved in terms of cost, power loss and size. Simultaneously, current information needs to be increasingly available in digital form to enable digital control, and to allow the digital transmission of the current information to a centralised monitoring and control unit. All this requires the output signal of a particular current sensing technique to be acquired by an analogue-to-digital converter, and thus the output voltage of the current sensor has to be sufficiently large. This thesis thoroughly reviews contemporary current sensing techniques and identifies suitable techniques that have the potential to meet the performance requirements of the next-generation of power converters. After the review chapter, three novel current sensing techniques are proposed and investigated: 1) The usefulness of the resistive voltage drop across a copper trace, which carries the current to be measured, to detect electrical current is evaluated. Simulations and experiments confirm that this inherently lossless technique can measure high currents at reasonable measurement bandwidth, good accuracy and low cost if the sense wires are connected properly. 2) Based on the mutual inductance theory found during the investigation of the copper trace current sense method, a modification of the well-known lossless inductor current sense method is proposed and analysed. This modification involves the use of a coupled sense winding that significantly improves the frequency response. Hence, it becomes possible to accurately monitor the output current of a power converter with the benefits of being lossless, exhibiting good sensitivity and having small size. 3) A transformer based DC current sense method is developed especially for digitally controlled power converters. This method provides high accuracy, large bandwidth, electrical isolation and very low thermal drift. Overall, it achieves better performance than many contemporary available Hall Effect sensors. At the same time, the cost of this current sensor is significantly lower than that of Hall Effect current sensors. A patent application has been submitted. .... The current sensing techniques have been studied by theory, hardware experiments and simulations. In addition, the suitability of the detection techniques for mass production has been considered in order to access the ability to provide systems at low-cost.
Download or read book Dissertation Abstracts International written by and published by . This book was released on 2008 with total page 980 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design of Power Management Integrated Circuits written by Bernhard Wicht and published by John Wiley & Sons. This book was released on 2024-05-14 with total page 484 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design of Power Management Integrated Circuits Comprehensive resource on power management ICs affording new levels of functionality and applications with cost reduction in various fields Design of Power Management Integrated Circuits is a comprehensive reference for power management IC design, covering the circuit design of main power management circuits like linear and switched-mode voltage regulators, along with sub-circuits such as power switches, gate drivers and their supply, level shifters, the error amplifier, current sensing, and control loop design. Circuits for protection and diagnostics, as well as aspects of the physical design like lateral and vertical power delivery, pin-out, floor planning, grounding/supply guidelines, and packaging, are also addressed. A full chapter is dedicated to the design of integrated passives. The text illustrates the application of power management integrated circuits (PMIC) to growth areas like computing, the Internet of Things, mobility, and renewable energy. Includes numerous real-world examples, case studies, and exercises illustrating key design concepts and techniques. Offering a unique insight into this rapidly evolving technology through the author’s experience developing PMICs in both the industrial and academic environment, Design of Power Management Integrated Circuits includes information on: Capacitive, inductive and hybrid DC-DC converters and their essential circuit blocks, covering error amplifiers, comparators, and ramp generators Sensing, protection, and diagnostics, covering thermal protection, inductive loads and clamping structures, under-voltage, reference and power-on reset generation Integrated MOS, MOM and MIM capacitors, integrated inductors Control loop design and PWM generation ensuring stability and fast transient response; subharmonic oscillations in current mode control (analysis and circuit design for slope compensation) DC behavior and DC-related circuit design, covering power efficiency, line and load regulation, error amplifier, dropout, and power transistor sizing Commonly used level shifters (including sizing rules) and cascaded (tapered) driver sizing and optimization guidelines Optimizing the physical design considering packaging, floor planning, EMI, pinout, PCB design and thermal design Design of Power Management Integrated Circuits is an essential resource on the subject for circuit designers/IC designers, system engineers, and application engineers, along with advanced undergraduate students and graduate students in related programs of study.
Download or read book Digitally Assisted Analog and Analog Assisted Digital IC Design written by Xicheng Jiang and published by Cambridge University Press. This book was released on 2015-07-23 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: Achieve enhanced performance with this guide to cutting-edge techniques for digitally-assisted analog and analog-assisted digital integrated circuit design. • Discover how architecture and circuit innovations can deliver improved performance in terms of speed, density, power, and cost • Learn about practical design considerations for high-performance scaled CMOS processes, FinFet devices and architectures, and the implications of FD SOI technology • Get up to speed with established circuit techniques that take advantage of scaled CMOS process technology in analog, digital, RF and SoC designs, including digitally-assisted techniques for data converters, DSP enabled frequency synthesizers, and digital controllers for switching power converters. With detailed descriptions, explanations, and practical advice from leading industry experts, this is an ideal resource for practicing engineers, researchers, and graduate students working in circuit design.
Download or read book A Self Calibration Reconstruction Circuit Applying to High Accuracy Current Sensing Technique for High Power Buck Converter written by and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Integrated Microsystems written by Krzysztof Iniewski and published by CRC Press. This book was released on 2017-12-19 with total page 760 pages. Available in PDF, EPUB and Kindle. Book excerpt: As rapid technological developments occur in electronics, photonics, mechanics, chemistry, and biology, the demand for portable, lightweight integrated microsystems is relentless. These devices are getting exponentially smaller, increasingly used in everything from video games, hearing aids, and pacemakers to more intricate biomedical engineering and military applications. Edited by Kris Iniewski, a revolutionary in the field of advanced semiconductor materials, Integrated Microsystems: Electronics, Photonics, and Biotechnology focuses on techniques for optimized design and fabrication of these intelligent miniaturized devices and systems. Composed of contributions from experts in academia and industry around the world, this reference covers processes compatible with CMOS integrated circuits, which combine computation, communications, sensing, and actuation capabilities. Light on math and physics, with a greater emphasis on microsystem design and configuration and electrical engineering, this book is organized in three sections—Microelectronics and Biosystems, Photonics and Imaging, and Biotechnology and MEMs. It addresses key topics, including physical and chemical sensing, imaging, smart actuation, and data fusion and management. Using tables, figures, and equations to help illustrate concepts, contributors examine and explain the potential of emerging applications for areas including biology, nanotechnology, micro-electromechanical systems (MEMS), microfluidics, and photonics.
Download or read book Proceedings written by and published by . This book was released on 2008 with total page 270 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Electrical Electronics Abstracts written by and published by . This book was released on 1997 with total page 2240 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Art of Electronics written by Paul Horowitz and published by . This book was released on 2021 with total page 1227 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Control and Nonlinear Dynamics on Energy Conversion Systems written by Herbert Ho-Ching Iu and published by MDPI. This book was released on 2019-07-01 with total page 435 pages. Available in PDF, EPUB and Kindle. Book excerpt: The ever-increasing need for higher efficiency, smaller size, and lower cost make the analysis, understanding, and design of energy conversion systems extremely important, interesting, and even imperative. One of the most neglected features in the study of such systems is the effect of the inherent nonlinearities on the stability of the system. Due to these nonlinearities, these devices may exhibit undesirable and complex dynamics, which are the focus of many researchers. Even though a lot of research has taken place in this area during the last 20 years, it is still an active research topic for mainstream power engineers. This research has demonstrated that these systems can become unstable with a direct result in increased losses, extra subharmonics, and even uncontrollability/unobservability. The detailed study of these systems can help in the design of smaller, lighter, and less expensive converters that are particularly important in emerging areas of research like electric vehicles, smart grids, renewable energy sources, and others. The aim of this Special Issue is to cover control and nonlinear aspects of instabilities in different energy conversion systems: theoretical, analysis modelling, and practical solutions for such emerging applications. In this Special Issue, we present novel research works in different areas of the control and nonlinear dynamics of energy conversion systems.
Download or read book Analysis and Design of Analog Integrated Circuits written by Paul R. Gray and published by John Wiley & Sons. This book was released on 2024-01-04 with total page 981 pages. Available in PDF, EPUB and Kindle. Book excerpt: ANALYSIS AND DESIGN OF ANALOG INTEGRATED CIRCUITS Authoritative and comprehensive textbook on the fundamentals of analog integrated circuits, with learning aids included throughout Written in an accessible style to ensure complex content can be appreciated by both students and professionals, this Sixth Edition of Analysis and Design of Analog Integrated Circuits is a highly comprehensive textbook on analog design, offering in-depth coverage of the fundamentals of circuits in a single volume. To aid in reader comprehension and retention, supplementary material includes end of chapter problems, plus a Solution Manual for instructors. In addition to the well-established concepts, this Sixth Edition introduces a new super-source follower circuit and its large-signal behavior, frequency response, stability, and noise properties. New material also introduces replica biasing, describes and analyzes two op amps with replica biasing, and provides coverage of weighted zero-value time constants as a method to estimate the location of dominant zeros, pole-zero doublets (including their effect on settling time and three examples of circuits that create doublets), the effect of feedback on pole-zero doublets, and MOS transistor noise performance (including a thorough treatment on thermally induced gate noise). Providing complete coverage of the subject, Analysis and Design of Analog Integrated Circuits serves as a valuable reference for readers from many different types of backgrounds, including senior undergraduates and first-year graduate students in electrical and computer engineering, along with analog integrated-circuit designers.
Download or read book Power Systems On Chip written by Bruno Allard and published by John Wiley & Sons. This book was released on 2016-11-22 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book gathers the major issues involved in the practical design of Power Management solutions in wireless products as Internet-of-things. Presentation is not about state-of-the-art but about appropriation of validated recent technologies by practicing engineers. The book delivers insights on major trade-offs and a presentation of examples as a cookbook. The content is segmented in chapters to make access easier for the lay-person.
Download or read book Solid State Technology written by and published by . This book was released on 1963 with total page 708 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modelling and Control of Switched Reluctance Machines written by Rui Araújo and published by BoD – Books on Demand. This book was released on 2020-09-09 with total page 373 pages. Available in PDF, EPUB and Kindle. Book excerpt: Today, switched reluctance machines (SRMs) play an increasingly important role in various sectors due to advantages such as robustness, simplicity of construction, low cost, insensitivity to high temperatures, and high fault tolerance. They are frequently used in fields such as aeronautics, electric and hybrid vehicles, and wind power generation. This book is a comprehensive resource on the design, modeling, and control of SRMs with methods that demonstrate their good performance as motors and generators.
Download or read book Power Supply Cookbook written by Marty Brown and published by Elsevier. This book was released on 2001-06-13 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power Supply Cookbook, Second Edition provides an easy-to-follow, step-by-step design framework for a wide variety of power supplies. With this book, anyone with a basic knowledge of electronics can create a very complicated power supply design in less than one day. With the common industry design approaches presented in each section, this unique book allows the reader to design linear, switching, and quasi-resonant switching power supplies in an organized fashion. Formerly complicated design topics such as magnetics, feedback loop compensation design, and EMI/RFI control are all described in simple language and design steps. This book also details easy-to-modify design examples that provide the reader with a design template useful for creating a variety of power supplies. This newly revised edition is a practical, "start-to-finish" design reference. It is organized to allow both seasoned and inexperienced engineers to quickly find and apply the information they need. Features of the new edition include updated information on the design of the output stages, selecting the controller IC, and other functions associated with power supplies, such as: switching power supply control, synchronization of the power supply to an external source, input low voltage inhibitors, loss of power signals, output voltage shut-down, major current loops, and paralleling filter capacitors. It also offers coverage of waveshaping techniques, major loss reduction techniques, snubbers, and quasi-resonant converters. - Guides engineers through a step-by-step design framework for a wide variety of power supplies, many of which can be designed in less than one day - Provides easy-to-understand information about often complicated topics, making power supply design a much more accessible and enjoyable process
