Download or read book In Situ Tests for the Determination of Rock Mass Shear Strength written by Timothy W. Zeigler and published by . This book was released on 1972 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rock shear strength is often determined from in situ tests. Many cases have been reported in the literature describing in situ shear test procedures and test results. The purpose of this report is to summarize this information for guidance in planning and evaluating such tests. The types of tests discussed are: direct shear test, Triaxial or multiaxial test, torsion shear test, and pull-out test. The direct shear test is most widely used, and some 48 case histories of such tests are summarized in Appendixes A through E. The main advantage of the direct shear test is the ability to measure the shear resistance in any desired direction along potentially critical discontinuities. The test is also popular due to its adaptability to field conditions; tests can be conducted in trenches, adits, tunnels, and even calyx drill holes. (Author).

Download or read book Correlations of Soil and Rock Properties in Geotechnical Engineering written by Jay Ameratunga and published by Springer. This book was released on 2015-12-11 with total page 236 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a one-stop reference to the empirical correlations used extensively in geotechnical engineering. Empirical correlations play a key role in geotechnical engineering designs and analysis. Laboratory and in situ testing of soils can add significant cost to a civil engineering project. By using appropriate empirical correlations, it is possible to derive many design parameters, thus limiting our reliance on these soil tests. The authors have decades of experience in geotechnical engineering, as professional engineers or researchers. The objective of this book is to present a critical evaluation of a wide range of empirical correlations reported in the literature, along with typical values of soil parameters, in the light of their experience and knowledge. This book will be a one-stop-shop for the practising professionals, geotechnical researchers and academics looking for specific correlations for estimating certain geotechnical parameters. The empirical correlations in the forms of equations and charts and typical values are collated from extensive literature review, and from the authors' database.

Download or read book Rock Characterisation Modelling and Engineering Design Methods written by Xia-Ting Feng and published by CRC Press. This book was released on 2013-05-17 with total page 932 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rock Characterisation, Modelling and Engineering Design Methods contains the contributions presented at the 3rd ISRM SINOROCK Symposium (Shanghai, China, 1820 June 2013). The papers contribute to the further development of the overall rock engineering design process through the sequential linkage of the three themes of rock characterisation, model

Download or read book Proceedings of the Indian Geotechnical Conference 2022 Volume 5 written by Babu T. Jose and published by Springer Nature. This book was released on with total page 517 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Rock Mechanics Based on an Anisotropic Jointed Rock Model AJRM written by Walter Wittke and published by John Wiley & Sons. This book was released on 2014-04-07 with total page 865 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dieses Buch konzentriert sich auf die Grundlagen der Felsmechanik als Basis für den sicheren und wirtschaftlichen Entwurf und Bau von Tunneln, Dämmen und Böschungen in geklüftetem und anisotropem Fels. Es ist in vier Hauptteile gegliedert: Grundlagen und Modelle Berechnungs- und Entwurfsmethoden Erkundungen, Versuche, Messung und Beobachtung Anwendungen und Fallbeispiele. Die felsmechanischen Modelle berücksichtigen den Einfluss von Trennflächen auf das Spannungs-Dehnungs-Verhalten und die Durchlässigkeit von geklüftetem Fels. Dieses Buch ist für: Bau- und Bergbauingenieure Geologen Studenten aus den entsprechenden Bereichen

Download or read book Engineering in Rock Masses written by F G Bell and published by Elsevier. This book was released on 2013-10-22 with total page 593 pages. Available in PDF, EPUB and Kindle. Book excerpt: Engineering in Rock Masses is a 26-chapter text that deals with the behavior, investigation, and construction of rock masses. The first chapters review the properties, behavior, classification, and occurrence of groundwater in rock masses. The subsequent chapters discuss the stress analysis, exploration, laboratory testing, geophysical methods, and instrumentation in these materials. These topics are followed by discussions of slope stability, rockfall problems, settlement and bearing capacity, subsidence, and seismic movements of rocks and rock masses. This work also evaluates the role of pumping system, ground freezing, grouting, rock anchors, drilling, blasting, and open excavation. The remaining chapters look into the rock masses’ tunneling, underground chambers, shafts, socketed foundations, and retaining structures. This book will be of great value to practicing civil and mining engineers, engineering geologists, and researchers.

Download or read book Rock Foundations written by United States. Army. Corps of Engineers and published by . This book was released on 1994 with total page 134 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Guidelines for Open Pit Slope Design written by John Read and published by CSIRO PUBLISHING. This book was released on 2009-11-09 with total page 511 pages. Available in PDF, EPUB and Kindle. Book excerpt: Guidelines for Open Pit Slope Design is a comprehensive account of the open pit slope design process. Created as an outcome of the Large Open Pit (LOP) project, an international research and technology transfer project on rock slope stability in open pit mines, this book provides an up-to-date compendium of knowledge of the slope design processes that should be followed and the tools that are available to aid slope design practitioners. This book links innovative mining geomechanics research into the strength of closely jointed rock masses with the most recent advances in numerical modelling, creating more effective ways for predicting rock slope stability and reliability in open pit mines. It sets out the key elements of slope design, the required levels of effort and the acceptance criteria that are needed to satisfy best practice with respect to pit slope investigation, design, implementation and performance monitoring. Guidelines for Open Pit Slope Design comprises 14 chapters that directly follow the life of mine sequence from project commencement through to closure. It includes: information on gathering all of the field data that is required to create a 3D model of the geotechnical conditions at a mine site; how data is collated and used to design the walls of the open pit; how the design is implemented; up-to-date procedures for wall control and performance assessment, including limits blasting, scaling, slope support and slope monitoring; and how formal risk management procedures can be applied to each stage of the process. This book will assist in meeting stakeholder requirements for pit slopes that are stable, in regards to safety, ore recovery and financial return, for the required life of the mine.

Download or read book Rock Quality Seismic Velocity Attenuation and Anisotropy written by Nick Barton and published by CRC Press. This book was released on 2006-11-03 with total page 756 pages. Available in PDF, EPUB and Kindle. Book excerpt: Seismic measurements take many forms, and appear to have a universal role in the Earth Sciences. They are the means for most easily and economically interpreting what lies beneath the visible surface. There are huge economic rewards and losses to be made when interpreting the shallow crust or subsurface more, or less accurately, as the case may be.

Download or read book Practical Engineering Geology written by Steve Hencher and published by CRC Press. This book was released on 2012-01-13 with total page 466 pages. Available in PDF, EPUB and Kindle. Book excerpt: Steve Hencher presents a broad and fresh view on the importance of engineering geology to civil engineering projects. Practical Engineering Geology provides an introduction to the way that projects are managed, designed and constructed and the ways that the engineering geologist can contribute to cost-effective and safe project achievement. The nee

Download or read book Engineering Rock Mass Classification written by R K Goel and published by Elsevier. This book was released on 2011-08-09 with total page 382 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rock mass classification methods are commonly used at the preliminary design stages of a construction project when there is very little information. It forms the bases for design and estimation of the required amount and type of rock support and groundwater control measures. Encompassing nearly all aspects of rock mass classifications in detail, Civil Engineering Rock Mass Classification: Tunnelling, Foundations and Landsides provides construction engineers and managers with extensive practical knowledge which is time-tested in the projects in Himalaya and other parts of the world in complex geological conditions. Rock mass classification is an essential element of feasibility studies for any near surface construction project prior to any excavation or disturbances made to earth. Written by an author team with over 50 years of experience in some of the most difficult mining regions of the world, Civil Engineering Rock Mass Classification: Tunnelling, Foundations and Landsides provides construction engineers, construction managers and mining engineers with the tools and methods to gather geotechnical data, either from rock cuts, drifts or core, and process the information for subsequent analysis. The goal is to use effective mapping techniques to obtain data can be used as input for any of the established rock classification systems. The book covers all of the commonly used classification methods including: Barton's Q and Q' systems, Bieniawski's RMR, Laubscher's MRMR and Hoek's and GSI systems. With this book in hand, engineers will be able to gather geotechnical data, either from rock cuts, drifts or core, and process the information for subsequent analysis. Rich with international case studies and worked out equations, the focus of the book is on the practical gathering information for purposes of analysis and design. - Identify the most significant parameters influencing the behaviour of a rock mass - Divide a particular rock mass formulation into groups of similar behaviour, rock mass classes of varying quality - Provide a basis of understanding the characteristics of each rock mass class - Relate the experience of rock conditions at one site to the conditions and experience encountered at others - Derive quantitative data and guidelines for engineering design - Provide common basis for communication between engineers and geologists

Download or read book Proceedings of the International Workshop on Rock Mass Classification in Underground Mining written by Christopher Mark and published by . This book was released on 2007 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Evaluation of Soil and Rock Properties written by P. J. Sabatini and published by . This book was released on 2004-10-01 with total page 392 pages. Available in PDF, EPUB and Kindle. Book excerpt: This document presents state-of-the-practice information on the evaluation of soil and rock properties for geotechnical design applications. This document addresses the entire range of materials potentially encountered in highway engineering practice, from soft clay to intact rock and variations of materials that fall between these two extremes. Information is presented on parameters measured, evaluation of data quality, and interpretation of properties for conventional soil and rock laboratory testing, as well as in situ devices such as field vane testing, cone penetration testing, dilatometer, pressuremeter, and borehole jack. This document provides the design engineer with information that can be used to develop a rationale for accepting or rejecting data and for resolving inconsistencies between data provided by different laboratories and field tests. This document also includes information on: (1) the use of Geographical Information Systems (GIS) and Personal Data Assistance devices for the collection and interpretation of subsurface information; (2) quantitative measures for evaluating disturbance of laboratory soil samples; and (3) the use of measurements from geophysical testing techniques to obtain information on the modulus of soil. Also included are chapters on evaluating properties of special soil materials (e.g., loess, cemented sands, peats and organic soils, etc.) and the use of statistical information in evaluating anomalous data and obtaining design values for soil and rock properties. An appendix of three detailed soil and rock property selection examples is provided which illustrate the application of the methods described in the document.

Download or read book Preparatory Excavation Works in Mines Volume I written by Prof. Dr. Bilal Semih Bozdemir and published by Prof. Dr. Bilal Semih Bozdemir. This book was released on with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: Methodology: The project utilized down-the-hole (DTH) drilling techniques due to the steep slopes and limited access to machinery. Blast designs were customized to ensure stability while avoiding excessive disturbance to the surrounding environment. A combination of emulsion and water-gel explosives was used to ensure safety and effectiveness in the challenging conditions. Challenges: One of the most prominent challenges was the unpredictability of rock conditions, which necessitated ongoing assessments and adjustments to the drilling and blasting parameters. Furthermore, the environmental protocol required strict adherence to minimize impact on local fauna and flora. Results: The successful completion of the pipeline installation not only fulfilled the project timeline but also maintained compliance with environmental standards. This case underscores the necessity of adaptive management strategies in drilling and blasting, particularly in sensitive environments where both safety and ecological considerations are paramount.

Download or read book Engineering Rock Mass Classifications written by Z. T. Bieniawski and published by John Wiley & Sons. This book was released on 1989-08-24 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the first authoritative reference on rock mass classification, consolidating into one handy source information once widely scattered throughout the literature. It includes new, previously unpublished material and case histories, presents the fundamental concepts of classification schemes, and critically appraises their practical application in industrial projects such as tunneling and mining.

Download or read book Support of Underground Excavations in Hard Rock written by E. Hoek and published by CRC Press. This book was released on 2000-01-01 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: The safe and economical construction of tunnels, mines, and other subterranean works depends on the correct choice of support systems to ensure that the excavations are stable. These support systems should be matched to the characterstics of the rock mass and the excavation techniques adopted. Establishing the support requirements, designing support systems and installing these correctly are essential elements in safe underground construction. This is a comprehensive and practical work which also gives access to user-friendly computer programmes which enable the investigation and design of support techniques. Details on how to obtain this software are also included in the book.

Download or read book Geotechnical Investigation Methods written by Roy E. Hunt and published by CRC Press. This book was released on 2006-10-31 with total page 352 pages. Available in PDF, EPUB and Kindle. Book excerpt: The investigation phase is the most important segment of any geotechnical study. Using the correct methods and properly interpreting the results are critical to a successful investigation. Comprising chapters from the second edition of the revered Geotechnical Engineering Investigation Handbook, Geotechnical Investigation Methods offers clear, conc