Download or read book Alloy Design and Characterization of Strengthened Nickel based Superalloys for Additive Manufacturing written by Jinghao Xu and published by Linköping University Electronic Press. This book was released on 2021-01-28 with total page 63 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nickel-based superalloys, an alloy system bases on nickel as the matrix element with the addition of up to 10 more alloying elements including chromium, aluminum, cobalt, tungsten, molybdenum, titanium, and so on. Through the development and improvement of nickel-based superalloys in the past century, they are well proved to show excellent performance at the elevated service temperature. Owing to the combination of extraordinary high-temperature mechanical properties, such as monotonic and cyclic deformation resistance, fatigue crack propagation resistance; and high-temperature chemical properties, such as corrosion and oxidation resistance, phase stability, nickel-based superalloys are widely used in the critical hot-section components in aerospace and energy generation industries. The success of nickel-based superalloy systems attributes to both the well-tailored microstructures with the assistance of carefully doped alloying elements, and the intently developed manufacturing processes. The microstructure of the modern nickel-based superalloys consists of a two-phase configuration: the intermetallic precipitates (Ni,Co)3(Al,Ti,Ta) known as γ′ phase dispersed into the austenite γ matrix, which is firstly introduced in the 1940s. The recently developed additive manufacturing (AM) techniques, acting as the disruptive manufacturing process, offers a new avenue for producing the nickel-based superalloy components with complicated geometries. However, γ′ strengthened nickel-based superalloys always suffer from the micro-cracking during the AM process, which is barely eliminated by the process optimization. On this basis, the new compositions of γ′ strengthened nickel-based superalloy adapted to the AM process are of great interest and significance. This study sought to design novel γ′ strengthened nickel-based superalloys readily for AM process with limited cracking susceptibility, based on the understanding of the cracking mechanisms. A two-parameter model is developed to predict the additive manufacturability for any given composition of a nickel-based superalloy. One materials index is derived from the comparison of the deformation-resistant capacity between dendritic and interdendritic regions, while another index is derived from the difference of heat resistant capacity of these two spaces. By plotting the additive manufacturability diagram, the superalloys family can be categorized into the easy-to-weld, fairly-weldable, and non-weldable regime with the good agreement of the existed knowledge. To design a novel superalloy, a Cr-Co-Mo-W-Al-Ti-Ta-Nb-Fe-Ni alloy family is proposed containing 921,600 composition recipes in total. Through the examination of additive manufacturability, undesired phase formation propensity, and the precipitation fraction, one composition of superalloy, MAD542, out of the 921,600 candidates is selected. Validation of additive manufacturability of MAD542 is carried out by laser powder bed fusion (LPBF). By optimizing the LPBF process parameters, the crack-free MAD542 part is achieved. In addition, the MAD542 superalloy shows great resistance to the post-processing treatment-induced cracking. During the post-processing treatment, extensive annealing twins are promoted to achieve the recrystallization microstructure, ensuring the rapid reduction of stored energy. After ageing treatment, up to 60-65% volume fraction of γ′ precipitates are developed, indicating the huge potential of γ′ formation. Examined by the high-temperature slow strain rate tensile and constant loading creep testing, the MAD542 superalloy shows superior strength than the LPBF processed and hot isostatic pressed plus heat-treated IN738LC superalloy. While the low ductility of MAD542 is existed, which is expected to be improved by modifying the post-processing treatment scenarios and by the adjusting building direction in the following stages of the Ph.D. research. MAD542 superalloy so far shows both good additive manufacturability and mechanical potentials. Additionally, the results in this study will contribute to a novel paradigm for alloy design and encourage more γ′-strengthened nickel-based superalloys tailored for AM processes in the future.

Download or read book Superalloys 2020 written by Sammy Tin and published by Springer Nature. This book was released on 2020-08-28 with total page 1098 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 14th International Symposium on Superalloys (Superalloys 2020) highlights technologies for lifecycle improvement of superalloys. In addition to the traditional focus areas of alloy development, processing, mechanical behavior, coatings, and environmental effects, this volume includes contributions from academia, supply chain, and product-user members of the superalloy community that highlight technologies that contribute to improving manufacturability, affordability, life prediction, and performance of superalloys.

Download or read book The Superalloys written by Roger C. Reed and published by Cambridge University Press. This book was released on 2008-07-31 with total page 363 pages. Available in PDF, EPUB and Kindle. Book excerpt: Superalloys are unique high-temperature materials used in gas turbine engines, which display excellent resistance to mechanical and chemical degradation. This book introduces the metallurgical principles which have guided their development. Suitable for graduate students and researchers, it includes exercises and additional resources at www.cambridge.org/9780521859042.

Download or read book Superalloys 2016 written by Mark C. Hardy and published by Wiley-TMS. This book was released on 2016-10-03 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the Proceedings 13th International Symposium on Superalloys

Download or read book Superalloys 2012 written by Eric S. Huron and published by John Wiley & Sons. This book was released on 2012-10-02 with total page 952 pages. Available in PDF, EPUB and Kindle. Book excerpt: A superalloy, or high-performance alloy, is an alloy that exhibits excellent mechanical strength at high temperatures. Superalloy development has been driven primarily by the aerospace and power industries. This compilation of papers from the Twelfth International Symposium on Superalloys, held from September 9-13, 2012, offers the most recent technical information on this class of materials.

Download or read book Superalloys written by Matthew J. Donachie and published by ASM International. This book was released on 2002 with total page 439 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers virtually all technical aspects related to the selection, processing, use, and analysis of superalloys. The text of this new second edition has been completely revised and expanded with many new figures and tables added. In developing this new edition, the focus has been on providing comprehensive and practical coverage of superalloys technology. Some highlights include the most complete and up-to-date presentation available on alloy melting. Coverage of alloy selection provides many tips and guidelines that the reader can use in identifying an appropriate alloy for a specific application. The relation of properties and microstructure is covered in more detail than in previous books.

Download or read book Nickel Cobalt and Their Alloys written by Joseph R. Davis and published by ASM International. This book was released on 2000-01-01 with total page 450 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive guide to the compositions, properties, processing, performance, and applications of nickel, cobalt, and their alloys. It includes all of the essential information contained in the ASM Handbook series, as well as new or updated coverage in many areas in the nickel, cobalt, and related industries.

Download or read book The Microstructure of Superalloys written by Madeleine Durand-Charre and published by Routledge. This book was released on 2017-11-22 with total page 139 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presents all the main aspects of the microstructure of nickel-base superalloys, and includes micrographs chosen from among a large range of commercial and academic alloys, from the as-cast product to in-situ components, worn from in-service use. Including more than 100 illustrations, the text explains all the transformation mechanisms involved in the origination (creation) of microstructures during solidification or heat treatments (crystallization paths, segregation, crystal orientation, precipitation, TCP, coarsening and rafting, etc.). It includes up-to-date information and data such as phase diagrams, crystallographic structures, and relationships with functional properties. Nearly 300 references provide a key to further investigation.

Download or read book Welding Metallurgy and Weldability written by John C. Lippold and published by John Wiley & Sons. This book was released on 2014-11-24 with total page 418 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describes the weldability aspects of structural materials used in a wide variety of engineering structures, including steels, stainless steels, Ni-base alloys, and Al-base alloys Welding Metallurgy and Weldability describes weld failure mechanisms associated with either fabrication or service, and failure mechanisms related to microstructure of the weldment. Weldability issues are divided into fabrication and service related failures; early chapters address hot cracking, warm (solid-state) cracking, and cold cracking that occur during initial fabrication, or repair. Guidance on failure analysis is also provided, along with examples of SEM fractography that will aid in determining failure mechanisms. Welding Metallurgy and Weldability examines a number of weldability testing techniques that can be used to quantify susceptibility to various forms of weld cracking. Describes the mechanisms of weldability along with methods to improve weldability Includes an introduction to weldability testing and techniques, including strain-to-fracture and Varestraint tests Chapters are illustrated with practical examples based on 30 plus years of experience in the field Illustrating the weldability aspects of structural materials used in a wide variety of engineering structures, Welding Metallurgy and Weldability provides engineers and students with the information needed to understand the basic concepts of welding metallurgy and to interpret the failures in welded components.

Download or read book Additively Manufactured Inconel 718 written by Dunyong Deng and published by Linköping University Electronic Press. This book was released on 2018-01-24 with total page 69 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM), also known as 3D printing, has gained significant interest in aerospace, energy, automotive and medical industries due to its capabilities of manufacturing components that are either prohibitively costly or impossible to manufacture by conventional processes. Among the various additive manufacturing processes for metallic components, electron beam melting (EBM) and selective laser melting (SLM) are two of the most widely used powder bed based processes, and have shown great potential for manufacturing high-end critical components, such as turbine blades and customized medical implants. The futures of the EBM and SLM are doubtlessly promising, but to fully realize their potentials there are still many challenges to overcome. Inconel 718 (IN718) is a nickel-base superalloy and has impressive combination of good mechanical properties and low cost. Though IN718 is being mostly used as a turbine disk material now, the initial introduction of IN718 was to overcome the poor weldability of superalloys in 1960s, since sluggish precipitation of strengthening phases ?’/?’’ enables good resistance to strain-age cracking during welding or post weld heat treatment. Given the similarity between AM and welding processes, IN718 has been widely applied to the metallic AM field to facilitate the understandings of process-microstructure-property relationships. The work presented in this licentiate thesis aims to better understand microstructures and mechanical properties EBM and SLM IN718, which have not been systematically investigated. Microstructures of EBM and SLM IN718 have been characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM) and correlated with the process conditions. Monotonic mechanical properties (e.g., Vickers microhardness and tensile properties) have also been measured and rationalized with regards to the microstructure evolutions before and after heat treatments. For EBM IN718, the results show the microstructure is not homogeneous but dependant on the location in the components, and the anisotropic mechanical properties are probably attributed to alignment of porosities rather than texture. Post heat treatment can slightly increase the mechanical strength compared to the as-manufactured condition but does not alter the anisotropy. SLM IN718 shows significantly different microstructure and mechanical properties to EBM IN718. The as-manufactured SLM IN718 has very fine dendritic microstructure and Laves phases in the interdendrites, and is “work-hardened” by the residual strains and dislocations present in the material. Mechanical properties are different between horizontally and vertically built samples, and heat treatment can minimize this difference. Results from this licentiate thesis provide the basis for the further research on the cyclic mechanical properties of EBM and SLM IN718, which would be the focus of following phase of the Ph.D. research.

Download or read book Additive Manufacturing of Metals written by John O. Milewski and published by Springer. This book was released on 2017-06-28 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This engaging volume presents the exciting new technology of additive manufacturing (AM) of metal objects for a broad audience of academic and industry researchers, manufacturing professionals, undergraduate and graduate students, hobbyists, and artists. Innovative applications ranging from rocket nozzles to custom jewelry to medical implants illustrate a new world of freedom in design and fabrication, creating objects otherwise not possible by conventional means. The author describes the various methods and advanced metals used to create high value components, enabling readers to choose which process is best for them. Of particular interest is how harnessing the power of lasers, electron beams, and electric arcs, as directed by advanced computer models, robots, and 3D printing systems, can create otherwise unattainable objects. A timeline depicting the evolution of metalworking, accelerated by the computer and information age, ties AM metal technology to the rapid evolution of global technology trends. Charts, diagrams, and illustrations complement the text to describe the diverse set of technologies brought together in the AM processing of metal. Extensive listing of terms, definitions, and acronyms provides the reader with a quick reference guide to the language of AM metal processing. The book directs the reader to a wealth of internet sites providing further reading and resources, such as vendors and service providers, to jump start those interested in taking the first steps to establishing AM metal capability on whatever scale. The appendix provides hands-on example exercises for those ready to engage in experiential self-directed learning.

Download or read book Cracking Phenomena in Welds IV written by Thomas Böllinghaus and published by Springer. This book was released on 2016-02-10 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the fourth volume in the well-established series of compendiums devoted to the subject of weld hot cracking. It contains the papers presented at the 4th International Cracking Workshop held in Berlin in April 2014. In the context of this workshop, the term “cracking” refers to hot cracking in the classical and previous sense, but also to cold cracking, stress-corrosion cracking and elevated temp. solid-state cracking. A variety of different cracking subjects are discussed, including test standards, crack prediction, weldability determination, crack mitigation, stress states, numerical modelling, and cracking mechanisms. Likewise, many different alloys were investigated such as aluminum alloys, copper-aluminum dissimilar metal, austenitic stainless steel, nickel base alloys, duplex stainless steel, creep resistant steel, and high strength steel.

Download or read book Laser Additive Manufacturing written by Milan Brandt and published by Woodhead Publishing. This book was released on 2016-09-01 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser Additive Manufacturing: Materials, Design, Technologies, and Applications provides the latest information on this highly efficient method of layer-based manufacturing using metals, plastics, or composite materials. The technology is particularly suitable for the production of complex components with high precision for a range of industries, including aerospace, automotive, and medical engineering. This book provides a comprehensive review of the technology and its range of applications. Part One looks at materials suitable for laser AM processes, with Part Two discussing design strategies for AM. Parts Three and Four review the most widely-used AM technique, powder bed fusion (PBF) and discuss other AM techniques, such as directed energy deposition, sheet lamination, jetting techniques, extrusion techniques, and vat photopolymerization. The final section explores the range of applications of laser AM. Provides a comprehensive one-volume overview of advances in laser additive manufacturing Presents detailed coverage of the latest techniques used for laser additive manufacturing Reviews both established and emerging areas of application

Download or read book Welding Metallurgy and Weldability of Nickel Base Alloys written by John C. Lippold and published by John Wiley & Sons. This book was released on 2011-09-20 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: The most up-to-date coverage of welding metallurgy aspects and weldability issues associated with Ni-base alloys Welding Metallurgy and Weldability of Nickel-Base Alloys describes the fundamental metallurgical principles that control the microstructure and properties of welded Ni-base alloys. It serves as a practical how-to guide that enables engineers to select the proper alloys, filler metals, heat treatments, and welding conditions to ensure that failures are avoided during fabrication and service. Chapter coverage includes: Alloying additions, phase diagrams, and phase stability Solid-solution strengthened Ni-base alloys Precipitation strengthened Ni-base alloys Oxide dispersion strengthened alloys and nickel aluminides Repair welding of Ni-base alloys Dissimilar welding Weldability testing High-chromium alloys used in nuclear power applications With its excellent balance between the fundamentals and practical problem solving, the book serves as an ideal reference for scientists, engineers, and technicians, as well as a textbook for undergraduate and graduate courses in welding metallurgy.

Download or read book Mechanical Alloying And Milling written by Cury Suryanarayana and published by CRC Press. This book was released on 2004-09-28 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book surveys the broad field of mechanical alloying from a scientific and technological perspective to form a timely and comprehensive resource valuable to both students and researchers. The treatment progresses from the historical background through a description of the process, the different metastable effects produced, and the mechanisms of

Download or read book The Design and Development of a New Nickel Base Superalloy WS 900 for Additive Manufacturing written by Husam Alrehaili and published by . This book was released on 2018 with total page 59 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ni-based superalloys are known for their ability to withstand and retain their mechanical and physical properties at elevated operating temperature, which makes them suitable for gas turbine and jet engine components. The outstanding properties of Ni-based superalloys have made them as an interesting candidate to process by Additive Manufacturing (AM). Although some Ni-based superalloys were successfully processed by AM, others were difficult to process by using this technique. Therefore, the need for new alloys, developed primarily for AM, has increased. This work presents a newly developed Ni-based superalloy "WSU 900" that was processed by using direct laser metal deposition (LMD) coupled with computational thermodynamics and phase diagram simulations. Microstructural and mechanical properties of the as-deposited and heat-treated WSU 900 alloy were studied. This new alloy shows good mechanical properties at room temperature. As-deposited condition revealed YS=951 MPa, UTS=1248 MPa, and elongation=19.2%. In the heat-treated conditions, 2 hours aged (YS=1076 MPa, UTS=1401 MPa, and elongation=14.9%), 8 hours aged (YS=1075 MPa, UTS=1376 MPa, and elongation=14.9 %), and 16 hours aged (YS=1162 MPa, UTS=1469 MPa, and elongation=11.9%).

Download or read book Additive Manufacturing Volume 2 written by Prashanth Konda Gokuldoss and published by MDPI. This book was released on 2020-04-15 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers and scientists, because of its ability to produce materials with a complex shape without theoretical restrictions and with added functionalities. There are several advantages to employing additive manufacturing as the primary additive manufacturing process. However, there exist several challenges that need to be addressed systematically. A couple such issues are alloy design and process development. Traditionally alloys designed for conventional cast/powder metallurgical processes were fabricated using advanced AM processes. This is the wrong approach considering that the alloys should be coined based on the process characteristics and meta-stable nature of the process. Hence, we must focus on alloy design and development for AM that suits the AM processes. The AM processes, however, improve almost every day, either in terms of processing capabilities or processing conditions. Hence, the processing part warrants a section that is devoted to these advancements and innovations. Accordingly, the present Special Issue (book) focuses on two aspects of alloy development and process innovations. Here, 45 articles are presented covering different AM processes including selective laser melting, electron beam melting, laser cladding, direct metal laser sintering, ultrasonic consolidation, wire arc additive manufacturing, and hybrid manufacturing. I believe that this Special Issue bears is vital to the field of AM and will be a valuable addition.