Download or read book AlGaN GaN HEMTs Reliability Degradation Modes and Analysis written by Ponky Ivo and published by Cuvillier. This book was released on 2012-10-25 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: AlGaN/GaN HEMTs reliability and stability issues were investigated in dependence on epitaxial design and process modification. DC-Step-Stress-Tests have been performed on wafers as a fast device robustness screening method. As a criterion of robustness they deliver a critical source-drain voltage for the onset of degradation. Several degradation modes were observed which depend on epi design, epi quality and process technology. Electrical and optical characterizations together with electric field simulations were performed to get insight into respective degradation modes. It has been found that AlGaN/GaN HEMT devices with GaN cap show higher critical source-drain voltages as compared to non-capped devices. Devices with low Al concentration in the AlGaN barrier layer also show higher critical source-drain voltages. Superior stability and robustness performance have been achieved from devices with AlGaN backbarrier epi design grown on n-type SiC substrate. For the onset on any degradation modes the presence of high electrical fields is most decisive for ON- and OFF-state operation conditions. Therefore careful epi design to reduce high electric field is mandatory. It is also shown that epi buffer quality and growth process have a great impact on device robustness. Defects such as point defects and dislocations are assumed to be created initially during stressing and accumulated to larger defect clusters during device stressing. Electroluminescence (EL) measurements were performed to detect early degradation. Extended localized defects are resulting as bright spots at OFF-state conditions in conjunction with a gate leakage increase.

Download or read book Thirty fourth International Symposium for Testing and Failure Analysis written by ASM International and published by ASM International. This book was released on 2008-01-01 with total page 551 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of RF and Microwave Power Amplifiers written by John L. B. Walker and published by Cambridge University Press. This book was released on 2012 with total page 705 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a one-stop guide for circuit designers and system/device engineers, covering everything from CAD to reliability.

Download or read book Nitride Semiconductor Technology written by Fabrizio Roccaforte and published by John Wiley & Sons. This book was released on 2020-07-17 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book "Nitride Semiconductor Technology" provides an overview of nitride semiconductors and their uses in optoelectronics and power electronics devices. It explains the physical properties of those materials as well as their growth methods. Their applications in high electron mobility transistors, vertical power devices, LEDs, laser diodes, and vertical-cavity surface-emitting lasers are discussed in detail. The book further examines reliability issues in these materials and puts forward perspectives of integrating them with 2D materials for novel high-frequency and high-power devices. In summary, it covers nitride semiconductor technology from materials to devices and provides the basis for further research.

Download or read book ReliabilityStudy Of Power Gallium Nitride Transistors written by and published by Marcon Denis. This book was released on with total page 229 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Power GaN Devices written by Matteo Meneghini and published by Springer. This book was released on 2016-09-08 with total page 383 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the first comprehensive overview of the properties and fabrication methods of GaN-based power transistors, with contributions from the most active research groups in the field. It describes how gallium nitride has emerged as an excellent material for the fabrication of power transistors; thanks to the high energy gap, high breakdown field, and saturation velocity of GaN, these devices can reach breakdown voltages beyond the kV range, and very high switching frequencies, thus being suitable for application in power conversion systems. Based on GaN, switching-mode power converters with efficiency in excess of 99 % have been already demonstrated, thus clearing the way for massive adoption of GaN transistors in the power conversion market. This is expected to have important advantages at both the environmental and economic level, since power conversion losses account for 10 % of global electricity consumption. The first part of the book describes the properties and advantages of gallium nitride compared to conventional semiconductor materials. The second part of the book describes the techniques used for device fabrication, and the methods for GaN-on-Silicon mass production. Specific attention is paid to the three most advanced device structures: lateral transistors, vertical power devices, and nanowire-based HEMTs. Other relevant topics covered by the book are the strategies for normally-off operation, and the problems related to device reliability. The last chapter reviews the switching characteristics of GaN HEMTs based on a systems level approach. This book is a unique reference for people working in the materials, device and power electronics fields; it provides interdisciplinary information on material growth, device fabrication, reliability issues and circuit-level switching investigation.

Download or read book Gallium Nitride enabled High Frequency and High Efficiency Power Conversion written by Gaudenzio Meneghesso and published by Springer. This book was released on 2018-05-12 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book demonstrates to readers why Gallium Nitride (GaN) transistors have a superior performance as compared to the already mature Silicon technology. The new GaN-based transistors here described enable both high frequency and high efficiency power conversion, leading to smaller and more efficient power systems. Coverage includes i) GaN substrates and device physics; ii) innovative GaN -transistors structure (lateral and vertical); iii) reliability and robustness of GaN-power transistors; iv) impact of parasitic on GaN based power conversion, v) new power converter architectures and vi) GaN in switched mode power conversion. Provides single-source reference to Gallium Nitride (GaN)-based technologies, from the material level to circuit level, both for power conversions architectures and switched mode power amplifiers; Demonstrates how GaN is a superior technology for switching devices, enabling both high frequency, high efficiency and lower cost power conversion; Enables design of smaller, cheaper and more efficient power supplies.

Download or read book A compact mode locked diode laser system for high precision frequency comparison experiments Band 64 written by Heike Christopher and published by Cuvillier Verlag. This book was released on 2021-04-09 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt: Optical frequency combs (OFC) have revolutionized various applications in applied and fundamental sciences that rely on the determination of absolute optical frequencies and frequency differences. The latter requires only stabilization of the spectral distance between the individual comb lines of the OFC, allowing to tailor and reduce system complexity of the OFC generator (OFCG). One such application is the quantum test of the universality of free fall within the QUANTUS experimental series. Within the test, the rate of free fall of two atomic species, Rb and K, in micro-gravity will be compared. The aim of this thesis was the development of a highly compact, robust, and space-suitable diode laser-based OFCG with a mode-locked optical spectrum in the wavelength range around 780 nm. A diode laser-based OFCG was developed, which exceeds the requirements with a spectral bandwidth > 16 nm at 20 dBc, a comb line optical power > 650 nW (at 20 dBc), a pulse repetition rate of 3.4 GHz, and an RF linewidth of the free-running pulse repetition rate < 10 kHz. To realize a proof-of-concept demonstrator module, the diode laser-based OFCG was hybrid-integrated into a space-suitable technology platform that has been developed for future QUANTUS experiments. Proof of sufficient RF stability of the OFCG was provided by stabilizing the pulse repetition rate to an external RF reference. This resulted in a stabilized pulse repetition rate with an RF linewidth smaller than 1.4 Hz (resolution limited), thus exceeding the requirement. The developed diode laser-based OFCG represents an important step towards an improved comparison of the rate of free fall of Rb and K quantum gases within the QUANTUS experiments in micro-gravity.

Download or read book A deep ultraviolet laser light source by frequency doubling of GaN based external cavity diode laser radiation written by Norman Ruhnke and published by Cuvillier Verlag. This book was released on 2022-05-13 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: A compact and portable laser light source emitting in the wavelength range between 210 nm and 230 nm would enable numerous applications outside of laboratory environments, such as sterilization and disinfection of medical equipment, water purification or gas and air analysis using absorption spectroscopy. Such a source is also highly attractive for the identification and quantification of proteins and biomolecules by means of laser-induced fluorescence or Raman spectroscopy. In this thesis, a novel concept to realize such a compact and portable laser light source with low power consumption and an emission around 222 nm is investigated. The developed concept is based on single-pass frequency doubling of a commercially available high-power GaN laser diode emitting in the blue spectral range. Due to the low frequency doubling conversion efficiencies in this wavelength range of about 10-4 W-1, a laser diode with high optical output power above 1 W is required as pump source. Moreover, it has to exhibit narrowband emission in the range of the acceptance bandwidth of the applied nonlinear BBO crystal. Since GaN-based high-power laser diodes typically show broad emission spectra of Δλ = 1…2 nm, stabilizing and narrowing their wavelength by using external wavelength-selective elements is investigated and presented for the first time. With the understanding for the novel concept gained in this work, a compact ultraviolet laser light source was realized. It has a power consumption of less than 10 W and is exceptionally robust due to its immoveable components. The demonstrated output power of 160 μW enables numerous industrial and everyday applications for which previous laser systems have been too complex and overly cost- and energy-intensive.

Download or read book AlN base layers for UV LEDs written by Sebastian Walde and published by Cuvillier Verlag. This book was released on 2021-06-22 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: To enable the fabrication of high performance ultraviolet (UV) light-emitting diodes (LEDs) this work aims at improving the quality of AlN base layers on sapphire substrates. The main issues for UV LEDs are still a limited internal quantum efficiency due to a high amount of threading dislocations along with a limited light extraction efficiency due to total internal reflection at the AlN/sapphire interface. Therefore, high-temperature annealing of AlN/sapphire layers and growth on nanopatterned sapphire substrates were comprehensively investigated. High-temperature annealing was applied to AlN layers of different strain and thickness grown by metalorganic vapour phase epitaxy (MOVPE). The threading dislocation density could be successfully reduced by more than one order of magnitude down to 6 × 108 cm-2. Wave optical simulations of UV LEDs on nanopatterned sapphire substrates (NPSS) were conducted and showed a potential increase in light extraction efficiency compared to a planar substrate. The optimized MOVPE growth process on sapphire nanopillars and sapphire nanoholes resulted in a fully coalesced and atomically smooth AlN surface. The threading dislocation density was reduced to 1 ×109 cm-2 for AlN on both nanopillars and nanoholes. UVC LEDs emitting at 265 nm wavelength were grown on top of the developed templates. Increased internal efficiency was obtained by reduced dislocation density and more efficient light extraction was achieved on NPSS in case of a transparent heterostructure and reflective contacts. Thus, the developed templates yield considerable improvement in light output compared to conventional templates.

Download or read book Two step MOVPE in situ etching and buried implantation applications to the realization of GaAs laser diodes written by Pietro della Casa and published by Cuvillier Verlag. This book was released on 2021-03-25 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work is about two-step epitaxial growth using metalorganic vapor-phase epitaxy (MOVPE) for the realization of edge-emitting near-infrared laser diodes. The fabricated gallium arsenide-based devices fall into two categories: high-power lasers (watt range, multimodal) and tunable lasers (milliwatt range, monomodal). Common to both cases is that surface contamination – particularly that due to oxygen – needs to be removed before regrowth. Thus, in-situ etching with carbon tetrabromide (CBr4) is first studied. The experimental results include kinetic data, the effects of different etching conditions as well as substrate characteristics, and the effectiveness in reducing surface contamination. These investigations pave the way to devices based on 2-step epitaxy combined with in-situ etching. Correspondingly, thermally-tuned SG-DBR lasers operating around 975 nm have been successfully realized, obtaining a tuning range of 21 nm. In addition, the possibility of using electronic tuning in similar devices has been explored. High-power broad-area lasers have also been realized, using two-step epitaxy combined with ex-situ and in-situ etching, to create a buried, shallow “mesa” containing the active zone. This approach allows introducing lateral electrical and optical confinement, and – simultaneously – non-absorbing mirrors at the laser facets. Additionally, a different strategy to create a buried current aperture is presented, which is based on ion implantation followed by epitaxial regrowth. This enables to improve device performance and simultaneously introduce non-absorbing mirrors at the facets with correspondingly increased reliability.

Download or read book Broad Area Laser Bars for 1 kW Emission written by Matthias M. Karow and published by Cuvillier Verlag. This book was released on 2022-06-27 with total page 143 pages. Available in PDF, EPUB and Kindle. Book excerpt: ndustrial laser systems for material processing applications rely on the availability of highly efficient, high-brightness diode lasers. GaAs-based broad-area laser bars play a vital role in such applications as pump sources for high-beam-quality solid-state lasers and, increasingly, as direct processing tools. This work studies 940 nm-laser bars emitting 1 kW optical power at room temperature, identifying those physical mechanisms that are currently limiting electrical-to-optical conversion efficiency as well as lateral beam quality. In the process, several diagnostic studies on bars with varied lateral-longitudinal design were carried out. The effects of technological measures for performance optimization were analyzed, yielding a new benchmark in efficiency and lateral divergence. The studies into altered resonator lengths of 4 and 6 mm as well as fill factors between 69 and 87 % successfully reduce both the voltage dropping across the device and power saturation at high currents, enabling 66 % efficiency at the operation point. Concrete measures how to reach efficiencies ≥70 % are presented thereafter, showing that doubling the efficiency value of the first 1 kW-demonstration in 2007 – amounting to 35 % – is in near reach. Investigation of the beam quality bases on a herein proposed and realized concept, in which the far field is resolved for each individual bar emitter. In this way, it is possible to determine how far-field profiles vary along the bar width and how much these variations affect the overall bar far-field. Further, such effects specific to bar structures can be separated into non-thermal and thermal influences. The effect of mechanical chip deformation (bar smile) as well as neighboring-emitter interaction has been investigated for the first time in active kW-class devices, yielding a lateral divergence as low as 8.8° at the operation point.

Download or read book Epitaxial Design Optimizations for Increased Efficiency in GaAs Based High Power Diode Lasers written by Thorben Kaul and published by Cuvillier Verlag. This book was released on 2021-04-09 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work presents progress in the root-cause analysis of power saturation mechanisms in continuous wave (CW) driven GaAs-based high-power broad area diode lasers operated at 935 nm. Target is to increase efficiency at high optical CW powers by epitaxial design. The novel extreme triple asymmetric (ETAS) design was developed and patented within this work to equip diode lasers that use an extremely thin p-waveguide with a high modal gain. An iterative variation of diode lasers employing ETAS designs was used to experimentally clarify the impact of modal gain on the temperature dependence of internal differential quantum efficiency (IDQE) and optical loss. High modal gain leads to increased free carrier absorption from the active region. However, less power saturation is observed, which must then be attributed to an improved temperature sensitivity of the IDQE. The effect of longitudinal spatial hole burning (LSHB) leads to above average non-linear carrier loss at the back facet of the device. At high CW currents the junction temperature rises. Therefore, not only the asymmetry of the carrier profile increases but also the average carrier density in order to compensate for the decreased material gain and increased threshold gain. This carrier non-pinning effect above threshold is found in this work to enhance the impact of LSHB already at low currents, leading to rapid degradation of IDQE with temperature. This finding puts LSHB into a new context for CW-driven devices as it emphasizes the importance of low carrier densities at threshold. The carrier density was effectively reduced by applying the novel ETAS design. This enabled diode lasers to be realized that show minimized degradation of IDQE with temperature and therefore improved performance in CW operation.

Download or read book Handbook of GaN Semiconductor Materials and Devices written by Wengang (Wayne) Bi and published by CRC Press. This book was released on 2017-10-20 with total page 775 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses material growth, device fabrication, device application, and commercialization of energy-efficient white light-emitting diodes (LEDs), laser diodes, and power electronics devices. It begins with an overview on basics of semiconductor materials, physics, growth and characterization techniques, followed by detailed discussion of advantages, drawbacks, design issues, processing, applications, and key challenges for state of the art GaN-based devices. It includes state of the art material synthesis techniques with an overview on growth technologies for emerging bulk or free standing GaN and AlN substrates and their applications in electronics, detection, sensing, optoelectronics and photonics. Wengang (Wayne) Bi is Distinguished Chair Professor and Associate Dean in the College of Information and Electrical Engineering at Hebei University of Technology in Tianjin, China. Hao-chung (Henry) Kuo is Distinguished Professor and Associate Director of the Photonics Center at National Chiao-Tung University, Hsin-Tsu, Taiwan, China. Pei-Cheng Ku is an associate professor in the Department of Electrical Engineering & Computer Science at the University of Michigan, Ann Arbor, USA. Bo Shen is the Cheung Kong Professor at Peking University in China.

Download or read book Springer Handbook of Semiconductor Devices written by Massimo Rudan and published by Springer Nature. This book was released on 2022-11-10 with total page 1680 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Springer Handbook comprehensively covers the topic of semiconductor devices, embracing all aspects from theoretical background to fabrication, modeling, and applications. Nearly 100 leading scientists from industry and academia were selected to write the handbook's chapters, which were conceived for professionals and practitioners, material scientists, physicists and electrical engineers working at universities, industrial R&D, and manufacturers. Starting from the description of the relevant technological aspects and fabrication steps, the handbook proceeds with a section fully devoted to the main conventional semiconductor devices like, e.g., bipolar transistors and MOS capacitors and transistors, used in the production of the standard integrated circuits, and the corresponding physical models. In the subsequent chapters, the scaling issues of the semiconductor-device technology are addressed, followed by the description of novel concept-based semiconductor devices. The last section illustrates the numerical simulation methods ranging from the fabrication processes to the device performances. Each chapter is self-contained, and refers to related topics treated in other chapters when necessary, so that the reader interested in a specific subject can easily identify a personal reading path through the vast contents of the handbook.

Download or read book Gallium Nitride Power Devices written by Hongyu Yu and published by CRC Press. This book was released on 2017-07-06 with total page 301 pages. Available in PDF, EPUB and Kindle. Book excerpt: GaN is considered the most promising material candidate in next-generation power device applications, owing to its unique material properties, for example, bandgap, high breakdown field, and high electron mobility. Therefore, GaN power device technologies are listed as the top priority to be developed in many countries, including the United States, the European Union, Japan, and China. This book presents a comprehensive overview of GaN power device technologies, for example, material growth, property analysis, device structure design, fabrication process, reliability, failure analysis, and packaging. It provides useful information to both students and researchers in academic and related industries working on GaN power devices. GaN wafer growth technology is from Enkris Semiconductor, currently one of the leading players in commercial GaN wafers. Chapters 3 and 7, on the GaN transistor fabrication process and GaN vertical power devices, are edited by Dr. Zhihong Liu, who has been working on GaN devices for more than ten years. Chapters 2 and 5, on the characteristics of polarization effects and the original demonstration of AlGaN/GaN heterojunction field-effect transistors, are written by researchers from Southwest Jiaotong University. Chapters 6, 8, and 9, on surface passivation, reliability, and package technologies, are edited by a group of researchers from the Southern University of Science and Technology of China.

Download or read book Nitride Wide Bandgap Semiconductor Material and Electronic Devices written by Yue Hao and published by CRC Press. This book was released on 2016-11-03 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book systematically introduces physical characteristics and implementations of III-nitride wide bandgap semiconductor materials and electronic devices, with an emphasis on high-electron-mobility transistors (HEMTs). The properties of nitride semiconductors make the material very suitable for electronic devices used in microwave power amplification, high-voltage switches, and high-speed digital integrated circuits.