Download or read book An Evaluation of the Uranium Contamination on the Surfaces of Alclad Uranium aluminum Alloy Research Reactor Fuel Plates written by R. J. Beaver and published by . This book was released on 1962 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Effect of Brake Forming in Various Tempers on the Strength of Alclad 75S T Aluminum alloy Sheet written by Walter Woods and published by . This book was released on 1947 with total page 530 pages. Available in PDF, EPUB and Kindle. Book excerpt: Results of presented of tests to determine the effect of brake forming in various tempers on the strength of Alclade 75S-T aluminum-alloy sheet in the direction parallel to the brake. The tensile and compressive strengths of Alclad 75S-T sheet, formed in the O and W tempers, were either increased or little affected as compared with those of similarly treated unformed material. When Alclad 75S-T sheet "as received" was formed, however, the tensile yield stress was reduced about 7 percent for the with-grain direction and 1 percent for the cross-grain direction, whereas the tensile ultimate and compressive yield strength stresses were increased somewhat. The elongation was always slightly reduced as a result of forming.

Download or read book The Fatigue Characteristics of Bolted Lap Joints of 24S T Alclad Sheet Materials written by L. R. Jackson and published by . This book was released on 1946 with total page 598 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue tests have been conducted to determine the effect of bolt fit upon the lifetime of lap joints of 24S-T Alclad sheet of various thicknesses joined by steel bolts an designed for sheet failure under repeated loading.

Download or read book The Effect of Artificial Aging on the Tensile Properties of Alclad 24S T and 24S T Aluminum Alloy written by Joseph N. Kotanchik and published by . This book was released on 1943 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: Summary: An experimental study was made to determine the effect of artificial aging on the tensile properties of alclad 24S-T and 24S-T aluminum-alloy sheet material. The results of the tests show that certain combinations of aging time and temperature cause a marked increase in the yield strength and a small increase in the ultimate strength; these increases are accompanied by a very large decrease in elongation. A curve is presented that shows the maximum yield strengths that can be obtained by aging this material at various combinations of time and temperature. The higher values of yield stress are obtained in material aged at relatively longer times and lower temperatures.

Download or read book Handbook of Aluminum written by George E. Totten and published by CRC Press. This book was released on 2003-04-25 with total page 744 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference provides thorough and in-depth coverage of the latest production and processing technologies encountered in the aluminum alloy industry, discussing current analytical methods for aluminum alloy characterization as well as extractive metallurgy, smelting, master alloy formation, and recycling. The Handbook of Aluminum: Volume 2 examin

Download or read book Technical Note National Advisory Committee for Aeronautics written by United States. National Advisory Committee for Aeronautics and published by . This book was released on 1950 with total page 1008 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Analysis of the Effects of Boundary layer Control on the Power off Landing Performance Characteristics of a Liaison Type of Airplane written by Elmer A. Horton and published by . This book was released on 1950 with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt: An investigation was made to determine the effects of boundary-layer control on the landing performance characteristics of a liaison type of airplane having a payload of 1500 pounds and a flight duration of 5 hours. The aspect ratio was varied from 5 to 15, the wing span from 30 to 100 feet, and the brake horsepower from 300 to 1200. The use of boundary-layer control caused reduction in total landing distance (25 to 40 percent), ground-run distance, gliding speed, and stalling speed whereas sinking speed was increased only slightly.

Download or read book Materials Survey Aluminum written by United States. Business and Defense Services Administration and published by . This book was released on 1956 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Materials Survey Aluminum written by United States. Business and Defense Services Administration. Aluminum and Magnesium Division and published by . This book was released on 1956 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Aviation written by and published by . This book was released on 1928 with total page 1082 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book NBS Special Publication written by and published by . This book was released on 1968 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Index of U S Voluntary Engineering Standards written by William J. Slattery and published by . This book was released on 1972 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Index of U S Voluntary Engineering Standards Supplement written by William J. Slattery and published by . This book was released on 1972 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Index of U S Voluntary Engineering Standards Supplement 1 written by William J. Slattery and published by . This book was released on 1972 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Annual Book of ASTM Standards written by American Society for Testing and Materials and published by . This book was released on 1981 with total page 1278 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Book of ASTM Standards with Related Material written by American Society for Testing and Materials and published by . This book was released on 1976 with total page 840 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Metals Alloys in the Unified Numbering System written by and published by SAE International. This book was released on 1993 with total page 486 pages. Available in PDF, EPUB and Kindle. Book excerpt: