Download or read book Aircraft Tire Wear Profile Development and Execution for Laboratory Testing written by A-5C Aircraft Tires Committee and published by . This book was released on 2018 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Information Report (AIR) describes the current process for performing comparative wear testing on aircraft tires in a laboratory environment. This technique is applicable to both radial and bias tires, and is pertinent for all aircraft tire sizes.This AIR describes a technique based upon "wear" energy. In this technique, side wear energy and drag wear energy are computed as the tire is run through a prescribed test program. The specifics that drive the test setup conditions are discussed in Sections 4 through 7. In general, the technique follows this process: A test profile is developed from measured mechanical property data of the tires under study. Each tire is repeatedly run to the test profile until it is worn to the maximum wear limit (MWL). Several tires, typically 5 to 10, of each tire design are tested. Wear energy is computed for each test cycle and then summed to determine total absorbed wear energy. An index is calculated for each tire design. This is accomplished by dividing the total linear inches of wear at the most worn point into the total wear energy. The indexes are then normalized to provide a comparative wear rate.The described technique is not meant to provide an absolute wear rate or wear index because the technique does not produce results that allow the user to say a tire will last for a specific number of landings. However, it does provide a comparative index. It will make a distinction from one tire design to another by indicating a percentage difference in abrasive wear rate under representative operational conditions. The technique has been demonstrated in a number of test programs and is shown to have an extremely high correlation to field data. Supporting data is included in Section 9. This document outlines a specific approach for testing use one particular facility. Revisions to this document are not anticipated and Five-Year Reviews have been determined to be unnecessary by the subcommittee. Therefore, it was agreed to stabilize this document.
Download or read book The Design of Aircraft Landing Gear written by Robert Kyle Schmidt and published by SAE International. This book was released on 2021-02-18 with total page 1092 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aircraft landing gear and its associated systems represent a compelling design challenge: simultaneously a system, a structure, and a machine, it supports the aircraft on the ground, absorbs landing and braking energy, permits maneuvering, and retracts to minimize aircraft drag. Yet, as it is not required during flight, it also represents dead weight and significant effort must be made to minimize its total mass. The Design of Aircraft Landing Gear, written by R. Kyle Schmidt, PE (B.A.Sc. - Mechanical Engineering, M.Sc. - Safety and Aircraft Accident Investigation, Chairman of the SAE A-5 Committee on Aircraft Landing Gear), is designed to guide the reader through the key principles of landing system design and to provide additional references when available. Many problems which must be confronted have already been addressed by others in the past, but the information is not known or shared, leading to the observation that there are few new problems, but many new people. The Design of Aircraft Landing Gear is intended to share much of the existing information and provide avenues for further exploration. The design of an aircraft and its associated systems, including the landing system, involves iterative loops as the impact of each modification to a system or component is evaluated against the whole. It is rare to find that the lightest possible landing gear represents the best solution for the aircraft: the lightest landing gear may require attachment structures which don't exist and which would require significant weight and compromise on the part of the airframe structure design. With those requirements and compromises in mind,The Design of Aircraft Landing Gear starts with the study of airfield compatibility, aircraft stability on the ground, the correct choice of tires, followed by discussion of brakes, wheels, and brake control systems. Various landing gear architectures are investigated together with the details of shock absorber designs. Retraction, kinematics, and mechanisms are studied as well as possible actuation approaches. Detailed information on the various hydraulic and electric services commonly found on aircraft, and system elements such as dressings, lighting, and steering are also reviewed. Detail design points, the process of analysis, and a review of the relevant requirements and regulations round out the book content. The Design of Aircraft Landing Gear is a landmark work in the industry, and a must-read for any engineer interested in updating specific skills and students preparing for an exciting career.
Download or read book Advances in Aircraft Brakes and Tires written by Robert Kyle Schmidt and published by SAE International. This book was released on 2015-08-24 with total page 126 pages. Available in PDF, EPUB and Kindle. Book excerpt: An aircraft’s interface with the ground—through its wheels, tires, and brakes—is critical to ensure safe and reliable operation, demanding constant technology development. Significant advancements have occurred with almost all civil airliners entering service with radial tires, and with the Boeing 787 having entered service in 2011 with electrically actuated carbon-carbon brakes. This book is divided into three sections: tires, control systems, and brakes, presenting a selection of the most relevant papers published by SAE International on these matters in the past fifteen years. They have been chosen to provide significant interest to those engineers working in the landing gear field. With almost all current large civil aircraft (and many smaller aircraft) opting exclusively for carbon-carbon brakes, a number of papers addressing the challenges of this technology are included. Papers touching on tire behavior and papers discussing brake control strategies are provided. For those looking for more information on aircraft landing gears, brakes, and tires, the SAE A-5 committee (the Aerospace Landing Gear Systems Committee), which meets twice a year, serves as a useful forum for discussion on landing gear issues and development. A current listing of documents produced and maintained by the A-5 committee is included in the appendix.
Download or read book Advances in Aircraft Landing Gear written by Robert Kyle Schmidt and published by SAE International. This book was released on 2015-08-24 with total page 138 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aircraft landing gear system is relatively unique on board an aircraft—it is both structure and machine, supporting the aircraft on the ground, yet providing functions such as energy absorption during landing, retraction, steering, and braking. Advances in Aircraft Landing Gear is a collection of eleven hand-picked technical papers focusing on the significant advancements that have occurred in this field concerning numeric modeling, electric actuation, and composite materials. Additionally, papers discussing self-powered landing gear and more electrical overall aircraft architectures have been included. The content of Advances in Aircraft Landing Gear is divided into two sections: Analysis and Design Methods; and Electric Actuation, Control, and Taxi. For those looking for more information on aircraft landing gears, the SAE A-5 committee (the Aerospace Landing Gear Systems Committee), which meets twice a year, serves as a useful forum for discussion on landing gear issues and development. A current listing of documents produced and maintained by this committee appears in the appendix.
Download or read book Development of an Operating Profile for Bias Aircraft Tires written by Paul Christian Durup and published by . This book was released on 1986 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes the procedures of analysis and dynamometer testing that were used to develop data and supporting technology for improving the maintenance and continued airworthiness of civil aircraft tires. As related to the inspection, retread and repair of aircraft tires under Advisory Circular AC 145-41, improved criteria which characterize typical tire operating environments and opening scenarios (associated with long range, medium range, and short haul transport airplanes) are defined. Based upon these criteria and scenarios which include tire loading, temperature, and roll distances, means to assess tire fatigue life were developed. Results of this effort may be used for the identification of in-service acceptance criteria and prescribed retread limits.
Download or read book Wear Friction and Temperature Characteristics of an Aircraft Tire Undergoing Braking and Cornering written by John L. McCarty and published by . This book was released on 1979 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1986 with total page 992 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Naval Aviation Maintenance Program NAMP Maintenance data systems written by United States. Office of the Chief of Naval Operations and published by . This book was released on 1990 with total page 870 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Safety Science Abstracts written by and published by . This book was released on 1975 with total page 514 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Commercial Aviation Safety Sixth Edition written by Stephen K. Cusick and published by McGraw Hill Professional. This book was released on 2017-05-12 with total page 561 pages. Available in PDF, EPUB and Kindle. Book excerpt: Up-To-Date Coverage of Every Aspect of Commercial Aviation Safety Completely revised edition to fully align with current U.S. and international regulations, this hands-on resource clearly explains the principles and practices of commercial aviation safety—from accident investigations to Safety Management Systems. Commercial Aviation Safety, Sixth Edition, delivers authoritative information on today's risk management on the ground and in the air. The book offers the latest procedures, flight technologies, and accident statistics. You will learn about new and evolving challenges, such as lasers, drones (unmanned aerial vehicles), cyberattacks, aircraft icing, and software bugs. Chapter outlines, review questions, and real-world incident examples are featured throughout. Coverage includes: • ICAO, FAA, EPA, TSA, and OSHA regulations • NTSB and ICAO accident investigation processes • Recording and reporting of safety data • U.S. and international aviation accident statistics • Accident causation models • The Human Factors Analysis and Classification System (HFACS) • Crew Resource Management (CRM) and Threat and Error Management (TEM) • Aviation Safety Reporting System (ASRS) and Flight Data Monitoring (FDM) • Aircraft and air traffic control technologies and safety systems • Airport safety, including runway incursions • Aviation security, including the threats of intentional harm and terrorism • International and U.S. Aviation Safety Management Systems
Download or read book Elastomere Friction written by Dieter Besdo and published by Springer. This book was released on 2016-05-01 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ERDA Energy Research Abstracts written by and published by . This book was released on 1983 with total page 1028 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1973 with total page 1122 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Physics of Tire Traction written by Donald Hays and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 423 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Energy Research Abstracts written by and published by . This book was released on 1983 with total page 864 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Friction Wear Lubrication written by Kenneth C Ludema and published by CRC Press. This book was released on 2018-09-14 with total page 309 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of a bestseller, this book introduces tribology in a way that builds students’ knowledge and understanding. It includes expanded information on topics such as surface characterization as well as recent advances in the field. The book provides additional descriptions of common testing methods, including diagrams and surface texturing for enhanced lubrication, and more information on rolling element bearings. It also explores surface profile characterization and elastic plastic contact mechanics including wavy surface contact, rough surface contact models, friction and wear plowing models, and thermodynamic analysis of friction.
Download or read book Flight test guide for certification of transport category airplanes written by and published by . This book was released on 1986 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt:
