Download or read book Advanced Combustion Systems for Next Generation Gas Turbines written by Joel Haynes and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Next generation turbine power plants will require high efficiency gas turbines with higher pressure ratios and turbine inlet temperatures than currently available. These increases in gas turbine cycle conditions will tend to increase NOx emissions. As the desire for higher efficiency drives pressure ratios and turbine inlet temperatures ever higher, gas turbines equipped with both lean premixed combustors and selective catalytic reduction after treatment eventually will be unable to meet the new emission goals of sub-3 ppm NOx. New gas turbine combustors are needed with lower emissions than the current state-of-the-art lean premixed combustors. In this program an advanced combustion system for the next generation of gas turbines is being developed with the goal of reducing combustor NOx emissions by 50% below the state-of-the-art. Dry Low NOx (DLN) technology is the current leader in NOx emission technology, guaranteeing 9 ppm NOx emissions for heavy duty F class gas turbines. This development program is directed at exploring advanced concepts which hold promise for meeting the low emissions targets. The trapped vortex combustor is an advanced concept in combustor design. It has been studied widely for aircraft engine applications because it has demonstrated the ability to maintain a stable flame over a wide range of fuel flow rates. Additionally, it has shown significantly lower NOx emission than a typical aircraft engine combustor and with low CO at the same time. The rapid CO burnout and low NOx production of this combustor made it a strong candidate for investigation. Incremental improvements to the DLN technology have not brought the dramatic improvements that are targeted in this program. A revolutionary combustor design is being explored because it captures many of the critical features needed to significantly reduce emissions. Experimental measurements of the combustor performance at atmospheric conditions were completed in the first phase of the program. Emissions measurements were obtained over a variety of operating conditions. A kinetics model is formulated to describe the emissions performance. The model is a tool for determining the conditions for low emission performance. The flow field was also modeled using CFD. A first prototype was developed for low emission performance on natural gas. The design utilized the tools anchored to the atmospheric prototype performance. The 1/6 scale combustor was designed for low emission performance in GE's FA+e gas turbine. A second prototype was developed to evaluate changes in the design approach. The prototype was developed at a 1/10 scale for low emission performance in GE's FA+e gas turbine. The performance of the first two prototypes gave a strong indication of the best design approach. Review of the emission results led to the development of a 3rd prototype to further reduce the combustor emissions. The original plan to produce a scaled-up prototype was pushed out beyond the scope of the current program. The 3rd prototype was designed at 1/10 scale and targeted further reductions in the full-speed full-load emissions.

Download or read book Advanced Combustion Systems for Stationary Gas Turbine Engines written by and published by . This book was released on 1980 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Combustion in Advanced Gas Turbine Systems written by I. E. Smith and published by Elsevier. This book was released on 2014-05-17 with total page 415 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cranfield International Symposium Series, Volume 10: Combustion in Advanced Gas Turbine Systems covers the proceedings of an International Propulsion Symposium, held at the College of Aeronautics in Cranfield in April 1967. The book focuses on the processes, methodologies, reactions, and transformations involved in chemical combustion. The selection first takes a look at the design considerations in advanced gas turbine combustion chambers, combustion in industrial gas turbines, and combustion development on the Rolls-Royce Spey engine. Discussions focus on mechanical condition, carbon-formation and exhaust smoke, system requirements, fuel oil ash deposition and corrosion, combustion-system design, performance requirements, types of primary zone, fuel injection, and combustion chamber types. The text then examines subsonic flow flameholder studies using a low pressure simulation technique; stabilization of hydrogen diffusion flames by flame-holders in supersonic flow at low stagnation temperatures; and augmentation systems for turbofan engines. The book takes a look at a consideration of the possible use of refractory ceramic materials for advanced combustion chamber design; cooling of flame tubes by steam injection; and combustion problems in the massive steam injection gas turbine. The selection is a valuable source of information for researchers interested in the process of combustion in advanced gas turbine systems.

Download or read book Advanced Technologies for Gas Turbines written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2020-04-19 with total page 137 pages. Available in PDF, EPUB and Kindle. Book excerpt: Leadership in gas turbine technologies is of continuing importance as the value of gas turbine production is projected to grow substantially by 2030 and beyond. Power generation, aviation, and the oil and gas industries rely on advanced technologies for gas turbines. Market trends including world demographics, energy security and resilience, decarbonization, and customer profiles are rapidly changing and influencing the future of these industries and gas turbine technologies. Technology trends that define the technological environment in which gas turbine research and development will take place are also changing - including inexpensive, large scale computational capabilities, highly autonomous systems, additive manufacturing, and cybersecurity. It is important to evaluate how these changes influence the gas turbine industry and how to manage these changes moving forward. Advanced Technologies for Gas Turbines identifies high-priority opportunities for improving and creating advanced technologies that can be introduced into the design and manufacture of gas turbines to enhance their performance. The goals of this report are to assess the 2030 gas turbine global landscape via analysis of global leadership, market trends, and technology trends that impact gas turbine applications, develop a prioritization process, define high-priority research goals, identify high-priority research areas and topics to achieve the specified goals, and direct future research. Findings and recommendations from this report are important in guiding research within the gas turbine industry and advancing electrical power generation, commercial and military aviation, and oil and gas production.

Download or read book Advanced Turbulent Combustion Modeling for Gas Turbine Application written by Andrea Donini and published by Andrea Donini. This book was released on with total page 173 pages. Available in PDF, EPUB and Kindle. Book excerpt: In spite of the increasing presence of renewable energy sources, fossil fuels will remain the primary supply of the world's energy needs for the upcoming future. Modern gas-turbine based systems represent one of the most efficient large-scale power generation technology currently available. Alongside this, gas-turbine power plants operate with very low emissions, have flexible operational characteristics and are able to utilize a broad range of fuels. It is expected that gas-turbine based plants will play an important role as an effective means of converting combustion energy in the future as well, because of the vast potential energy savings. The numerical approach to the design of complex systems such as gas-turbines has gained a continuous growth of interest in the last few decades. This because simulations are foreseen to provide a tremendous increase in the combustor efficiency, fuel-flexibility and quality over the next future. In this dissertation, an advanced turbulent combustion technique is implemented and progressively developed for the simulation of all the features that are typically observed in stationary gas-turbine combustion, including hydrogen as a fuel. The developed turbulent combustion model retains most of the accuracy of a detailed simulation while drastically reducing its computational time. As a result of this work, the advancement of power generation plants can be accelerated, paving the way for future developments of alternative fuel usage in a cleaner and more efficient combustion.

Download or read book Advanced Technologies for Gas Turbines written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2020-03-19 with total page 137 pages. Available in PDF, EPUB and Kindle. Book excerpt: Leadership in gas turbine technologies is of continuing importance as the value of gas turbine production is projected to grow substantially by 2030 and beyond. Power generation, aviation, and the oil and gas industries rely on advanced technologies for gas turbines. Market trends including world demographics, energy security and resilience, decarbonization, and customer profiles are rapidly changing and influencing the future of these industries and gas turbine technologies. Technology trends that define the technological environment in which gas turbine research and development will take place are also changing - including inexpensive, large scale computational capabilities, highly autonomous systems, additive manufacturing, and cybersecurity. It is important to evaluate how these changes influence the gas turbine industry and how to manage these changes moving forward. Advanced Technologies for Gas Turbines identifies high-priority opportunities for improving and creating advanced technologies that can be introduced into the design and manufacture of gas turbines to enhance their performance. The goals of this report are to assess the 2030 gas turbine global landscape via analysis of global leadership, market trends, and technology trends that impact gas turbine applications, develop a prioritization process, define high-priority research goals, identify high-priority research areas and topics to achieve the specified goals, and direct future research. Findings and recommendations from this report are important in guiding research within the gas turbine industry and advancing electrical power generation, commercial and military aviation, and oil and gas production.

Download or read book Gas Turbines for Electric Power Generation written by S. Can Gülen and published by Cambridge University Press. This book was released on 2019-02-14 with total page 735 pages. Available in PDF, EPUB and Kindle. Book excerpt: Everything you wanted to know about industrial gas turbines for electric power generation in one source with hard-to-find, hands-on technical information.

Download or read book Advanced Combustion and Aerothermal Technologies written by Nick Syred and published by Springer. This book was released on 2007-10-16 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt: Here readers will find a summary of proceedings at a highly important NATO workshop. The ARW Advanced Combustion and Aerothermal Technologies: Environmental Protection and Pollution Reductions, was held in Kiev, May 2006. The workshop was co-directed by Profs. N. Syred and A.Khalatov, winners of the NATO Scientific Prize 2002, and was organized by the Institute of Thermophysics (Ukraine) and Cardiff University, UK. The primary workshop objective was to assess the existing knowledge on advanced combustion and aerothermal technologies providing reduced environmental impact.

Download or read book ADVANCED TURBINE SYSTEMS PROGRAM written by Gregory Gaul and published by . This book was released on 2004 with total page 261 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural gas combustion turbines are rapidly becoming the primary technology of choice for generating electricity. At least half of the new generating capacity added in the US over the next twenty years will be combustion turbine systems. The Department of Energy has cosponsored with Siemens Westinghouse, a program to maintain the technology lead in gas turbine systems. The very ambitious eight year program was designed to demonstrate a highly efficient and commercially acceptable power plant, with the ability to fire a wide range of fuels. The main goal of the Advanced Turbine Systems (ATS) Program was to develop ultra-high efficiency, environmentally superior and cost effective competitive gas turbine systems for base load application in utility, independent power producer and industrial markets. Performance targets were focused on natural gas as a fuel and included: System efficiency that exceeds 60% (lower heating value basis); Less than 10 ppmv NO{sub x} emissions without the use of post combustion controls; Busbar electricity that are less than 10% of state of the art systems; Reliability-Availability-Maintainability (RAM) equivalent to current systems; Water consumption minimized to levels consistent with cost and efficiency goals; and Commercial systems by the year 2000. In a parallel effort, the program was to focus on adapting the ATS engine to coal-derived or biomass fuels. In Phase 1 of the ATS Program, preliminary investigators on different gas turbine cycles demonstrated that net plant LHV based efficiency greater than 60% was achievable. In Phase 2 the more promising cycles were evaluated in greater detail and the closed-loop steam-cooled combined cycle was selected for development because it offered the best solution with least risk for achieving the ATS Program goals for plant efficiency, emissions, cost of electricity and RAM. Phase 2 also involved conceptual ATS engine and plant design and technology developments in aerodynamics, sealing, combustion, cooling, materials, coatings and casting development. The market potential for the ATS gas turbine in the 2000-2014 timeframe was assessed for combined cycle, simple cycle and integrated gasification combined cycle, for three engine sizes. The total ATS market potential was forecasted to exceed 93 GW. Phase 3 and Phase 3 Extension involved further technology development, component testing and W501ATS engine detail design. The technology development efforts consisted of ultra low NO{sub x} combustion, catalytic combustion, sealing, heat transfer, advanced coating systems, advanced alloys, single crystal casting development and determining the effect of steam on turbine alloys. Included in this phase was full-load testing of the W501G engine at the McIntosh No. 5 site in Lakeland, Florida.

Download or read book Advanced Power Generation Systems written by Ibrahim Dincer and published by Academic Press. This book was released on 2014-07-15 with total page 657 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Power Generation Systems examines the full range of advanced multiple output thermodynamic cycles that can enable more sustainable and efficient power production from traditional methods, as well as driving the significant gains available from renewable sources. These advanced cycles can harness the by-products of one power generation effort, such as electricity production, to simultaneously create additional energy outputs, such as heat or refrigeration. Gas turbine-based, and industrial waste heat recovery-based combined, cogeneration, and trigeneration cycles are considered in depth, along with Syngas combustion engines, hybrid SOFC/gas turbine engines, and other thermodynamically efficient and environmentally conscious generation technologies. The uses of solar power, biomass, hydrogen, and fuel cells in advanced power generation are considered, within both hybrid and dedicated systems. The detailed energy and exergy analysis of each type of system provided by globally recognized author Dr. Ibrahim Dincer will inform effective and efficient design choices, while emphasizing the pivotal role of new methodologies and models for performance assessment of existing systems. This unique resource gathers information from thermodynamics, fluid mechanics, heat transfer, and energy system design to provide a single-source guide to solving practical power engineering problems. The only complete source of info on the whole array of multiple output thermodynamic cycles, covering all the design options for environmentally-conscious combined production of electric power, heat, and refrigeration Offers crucial instruction on realizing more efficiency in traditional power generation systems, and on implementing renewable technologies, including solar, hydrogen, fuel cells, and biomass Each cycle description clarified through schematic diagrams, and linked to sustainable development scenarios through detailed energy, exergy, and efficiency analyses Case studies and examples demonstrate how novel systems and performance assessment methods function in practice

Download or read book Advanced Combustion Systems for Stationary Gas Turbine Engines Vol I written by U S Environmental Protection Agency and published by Scholar's Choice. This book was released on 2015-02-16 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work has been selected by scholars as being culturally important, and is part of the knowledge base of civilization as we know it. This work was reproduced from the original artifact, and remains as true to the original work as possible. Therefore, you will see the original copyright references, library stamps (as most of these works have been housed in our most important libraries around the world), and other notations in the work. This work is in the public domain in the United States of America, and possibly other nations. Within the United States, you may freely copy and distribute this work, as no entity (individual or corporate) has a copyright on the body of the work.As a reproduction of a historical artifact, this work may contain missing or blurred pages, poor pictures, errant marks, etc. Scholars believe, and we concur, that this work is important enough to be preserved, reproduced, and made generally available to the public. We appreciate your support of the preservation process, and thank you for being an important part of keeping this knowledge alive and relevant.

Download or read book Combustion in Advanced Gas Turbine Systems written by Ian Edward Smith and published by . This book was released on 1968 with total page 426 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Advances in Gas Turbine Technology written by Ernesto Benini and published by BoD – Books on Demand. This book was released on 2011-11-04 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbine engines will still represent a key technology in the next 20-year energy scenarios, either in stand-alone applications or in combination with other power generation equipment. This book intends in fact to provide an updated picture as well as a perspective vision of some of the major improvements that characterize the gas turbine technology in different applications, from marine and aircraft propulsion to industrial and stationary power generation. Therefore, the target audience for it involves design, analyst, materials and maintenance engineers. Also manufacturers, researchers and scientists will benefit from the timely and accurate information provided in this volume. The book is organized into five main sections including 21 chapters overall: (I) Aero and Marine Gas Turbines, (II) Gas Turbine Systems, (III) Heat Transfer, (IV) Combustion and (V) Materials and Fabrication.

Download or read book Fuel Flexible Combustion System for Co production Plant Applications written by and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Future high-efficiency, low-emission generation plants that produce electric power, transportation fuels, and/or chemicals from fossil fuel feed stocks require a new class of fuel-flexible combustors. In this program, a validated combustor approach was developed which enables single-digit NO(subscript x) operation for a future generation plants with low-Btu off gas and allows the flexibility of process-independent backup with natural gas. This combustion technology overcomes the limitations of current syngas gas turbine combustion systems, which are designed on a site-by-site basis, and enable improved future co-generation plant designs. In this capacity, the fuel-flexible combustor enhances the efficiency and productivity of future co-production plants. In task 2, a summary of market requested fuel gas compositions was created and the syngas fuel space was characterized. Additionally, a technology matrix and chemical kinetic models were used to evaluate various combustion technologies and to select two combustor concepts. In task 4 systems analysis of a co-production plant in conjunction with chemical kinetic analysis was performed to determine the desired combustor operating conditions for the burner concepts. Task 5 discusses the experimental evaluation of three syngas capable combustor designs. The hybrid combustor, Prototype-1 utilized a diffusion flame approach for syngas fuels with a lean premixed swirl concept for natural gas fuels for both syngas and natural gas fuels at FA+e gas turbine conditions. The hybrid nozzle was sized to accommodate syngas fuels ranging from (almost equal to)100 to 280 btu/scf and with a diffusion tip geometry optimized for Early Entry Co-generation Plant (EECP) fuel compositions. The swozzle concept utilized existing GE DLN design methodologies to eliminate flow separation and enhance fuel-air mixing. With changing business priorities, a fully premixed natural gas & syngas nozzle, Protoytpe-1N, was also developed later in the program. It did not have the diluent requirements of Prototype-1 and was demonstrated at targeted gas turbine conditions. The TVC combustor, Prototype-2, premixes the syngas with air for low emission performance. The combustor was designed for operation with syngas and no additional diluents. The combustor was successfully operated at targeted gas turbine conditions. Another goal of the program was to advance the status of development tools for syngas systems. In Task 3 a syngas flame evaluation facility was developed. Fundamental data on syngas flame speeds and flame strain were obtained at pressure for a wide range of syngas fuels with preheated air. Several promising reduced order kinetic mechanisms were compared with the results from the evaluation facility. The mechanism with the best agreement was selected for application to syngas combustor modeling studies in Task 6. Prototype-1 was modeled using an advanced LES combustion code. The tools and combustor technology development culminate in a full-scale demonstration of the most promising technology in Task 8. The combustor was operated at engine conditions and evaluated against the various engine performance requirements.

Download or read book Task 8 2 Subscale Catalytic Combustor Development written by and published by . This book was released on 1996 with total page 35 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Solar/DOE ATS engine program seeks to reduce engine pollutant emissions to single digit levels and low pattern factor. Program goals include the attainment of emissions (NOx, CO and UHC corrected to 15% O2) below 10 ppmvd over the 50 to 100% load range, pattern factor less than 0.2, and long term combustor component durability. Recent improvements in Solar's dry low NOx combustion technology guarantee less than 25 ppmvd NOx and 50 ppmvd CO (@ 15% O2) in field units. It is expected that with the incorporation of advanced combustion technology (e.g. variable geometry, use of ceramics in combustion liners, improved CO sensor based control systems, improved fuel-air premixing, advanced liner cooling, etc.) into present combustion systems, substantial reductions in emissions over currently guaranteed levels will be possible. However, the next generation of low emissions gas turbines may be required to incorporate catalytic combustion to guarantee the lowest possible levels of pollutant emissions with available technology, As part of the Solar ATS Phase II program, catalytic combustion was selected as the primary combustion approach capable of attaining the emissions goals of the ATS program for medium sized industrial gas turbines. Catalytic combustion technology development in Phase II consisted of two main tasks: Task 2.8.2 involving the evaluation and demonstration of catalytic combustion technology at simulated engine conditions in a subscale rig environment, and Task 2.8.5 involving the design and evaluation of a single can full scale catalytic combustion system based on subscale results. Successful full scale rig operation will be followed by sector rig testing, and the procurement of a full set of engine hardware for an engine demonstration as part of Solar ATS Phase III program, If successful in the ATS program, catalytic combustion will be introduced in Solar's production turbines depending on market requirements and cost.

Download or read book Gas Turbine Engineering Handbook written by Meherwan P. Boyce and published by Elsevier. This book was released on 2017-09-01 with total page 956 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Gas Turbine Engineering Handbook has been the standard for engineers involved in the design, selection, and operation of gas turbines. This revision includes new case histories, the latest techniques, and new designs to comply with recently passed legislation. By keeping the book up to date with new, emerging topics, Boyce ensures that this book will remain the standard and most widely used book in this field. The new Third Edition of the Gas Turbine Engineering Hand Book updates the book to cover the new generation of Advanced gas Turbines. It examines the benefit and some of the major problems that have been encountered by these new turbines. The book keeps abreast of the environmental changes and the industries answer to these new regulations. A new chapter on case histories has been added to enable the engineer in the field to keep abreast of problems that are being encountered and the solutions that have resulted in solving them. Comprehensive treatment of Gas Turbines from Design to Operation and Maintenance. In depth treatment of Compressors with emphasis on surge, rotating stall, and choke; Combustors with emphasis on Dry Low NOx Combustors; and Turbines with emphasis on Metallurgy and new cooling schemes. An excellent introductory book for the student and field engineers A special maintenance section dealing with the advanced gas turbines, and special diagnostic charts have been provided that will enable the reader to troubleshoot problems he encounters in the field The third edition consists of many Case Histories of Gas Turbine problems. This should enable the field engineer to avoid some of these same generic problems

Download or read book Combustion for Power Generation and Transportation written by Avinash Kumar Agarwal and published by Springer. This book was released on 2017-01-20 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: This research monograph presents both fundamental science and applied innovations on several key and emerging technologies involving fossil and alternate fuel utilization in power and transport sectors from renowned experts in the field. Some of the topics covered include: autoignition in laminar and turbulent nonpremixed flames; Langevin simulation of turbulent combustion; lean blowout (LBO) prediction through symbolic time series analysis; lasers and optical diagnostics for next generation IC engine development; exergy destruction study on small DI diesel engine; and gasoline direct injection. The book includes a chapter on carbon sequestration and optimization of enhanced oil and gas recovery. The contents of this book will be useful to researchers and professionals working on all aspects on combustion.