Download or read book Adhesive Bonding of Polymeric Materials for Automotive Applications written by and published by . This book was released on 1994 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: In 1992, the Oak Ridge National Laboratory (ORNL) began a cooperative research program with the Automotive Composites Consortium (ACC) to develop technologies that would overcome obstacles to the adhesive bonding of current and future automotive materials. This effort is part of a larger Department of Energy (DOE) program to promote the use of lighter weight materials in automotive structures. By reducing the weight of current automobiles, greater fuel economy and reduced emissions can be achieved. The bonding of similar and dissimilar materials was identified as being of primary importance since this enabling technology gives designers the freedom to choose from an expanded menu of low-mass materials for structural component weight reduction. Early in the project's conception, five key areas were identified as being of primary importance to the automotive industry.
Download or read book Adhesion Science and Engineering written by and published by Elsevier. This book was released on 2002-11-14 with total page 2020 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Mechanics of Adhesion shows that adhesion science and technology is inherently an interdisciplinary field, requiring fundamental understanding of mechanics, surfaces, and materials. This volume comprises 19 chapters. Starting with a background and introduction to stress transfer principles; fracture mechanics and singularities; and an energy approach to debonding, the volume continues with analysis of structural lap and butt joint configurations. It then continues with discussions of test methods for strength and constitutive properties; fracture; peel; coatings, the case of adhesion to a single substrate; elastomeric adhesives such as sealants. The role of mechanics in determining the locus of failure in bonded joints is discussed, followed by a chapter on rheology relevant to adhesives and sealants. Pressure sensitive adhesive performance; the principles of tack and tack measurements; and contact mechanics relevant to wetting and surface energy measurements are then covered. The volume concludes with sections on fibermatrix bonding and reinforcement; durability considerations for adhesive bonds; ultrasonic non-destructive evaluation of adhesive bonds; and design of adhesive bonds from a strength perspective. This book will be of interest to practitioners in the fields of engineering and to those with an interest in adhesion science.
Download or read book Advances in Structural Adhesive Bonding written by David A. Dillard and published by Elsevier. This book was released on 2010-03-31 with total page 654 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesive bonding is often effective, efficient, and often necessary way to join mechanical structures. This important book reviews the most recent improvements in adhesive bonding and their wide-ranging potential in structural engineering.Part one reviews advances in the most commonly used groups of structural adhesives with chapters covering topics such as epoxy, polyurethane, silicone, cyanoacrylate, and acrylic adhesives. The second set of chapters covers the various types of adherends and pre-treatment methods for a range of structural materials such as metals, composites and plastics. Chapters in Part three analyse methods and techniques with topics on joint design, life prediction, fracture mechanics and testing. The final group of chapters gives useful and practical insights into the problems and solutions of adhesive bonding in a variety of hostile environments such as chemical, wet and extreme temperatures.With its distinguished editor and international team of contributors, Advances in structural adhesive bonding is a standard reference for structural and chemical engineers in industry and the academic sector. - Reviews advances in the most commonly used groups of structural adhesives including epoxy, silicone and acrylic adhesives - Examines key issues in adhesive selection featuring substrate compatibility and manufacturing demands - Documents advances in bonding metals, plastics and composites recognising problems and limitations
Download or read book Adhesive Bonding written by Robert D. Adams and published by Elsevier. This book was released on 2005-03-08 with total page 560 pages. Available in PDF, EPUB and Kindle. Book excerpt: This important collection reviews key research on adhesive behaviour and applications in sectors as diverse as construction and automotive engineering. The book is divided into three main parts: fundamentals, mechanical properties and applications. Part one focuses on the basic properties of adhesives, surface assessment and treatment. Part two concentrates on understanding how adhesives perform under stress and the factors affecting fatigue and failure. The final part of the book reviews industry specific applications in areas such as building and construction, transport and electrical engineering.With its distinguished editor and international team of contributors, Adhesive bonding is a standard reference for all those concerned with the industrial application of adhesives. - Essential information for all those concerned with the industrial application of adhesives - This important collection examines adhesives and adhesive bonding for load-bearing applications - Arranged in a user-friendly format with three main sections: fundamentals, generic uses and industry specific applications
Download or read book Joining of Polymer Metal Hybrid Structures written by Sergio T. Amancio Filho and published by John Wiley & Sons. This book was released on 2017-12-27 with total page 420 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive introduction to the concepts of joining technologies for hybrid structures This book introduces the concepts of joining technology for polymer-metal hybrid structures by addressing current and new joining methods. This is achieved by using a balanced approach focusing on the scientific features (structural, physical, chemical, and metallurgical/polymer science phenomena) and engineering properties (mechanical performance, design, applications, etc.) of the currently available and new joining processes. It covers such topics as mechanical fastening, adhesive bonding, advanced joining methods, and statistical analysis in joining technology. Joining of Polymer-Metal Hybrid Structures: Principles and Applications is structured by joining principles, in adhesion-based, mechanical fastened, and direct-assembly methods. The book discusses such recent technologies as friction riveting, friction spot joining and ultrasonic joining. This is used for applications where the original base material characteristics must remain unchanged. Additional sections cover the main principles of statistical analysis in joining technology (illustrated with examples from the field of polymer-metal joining). Joining methods discussed include mechanical fastening (bolting, screwing, riveting, hinges, and fits of polymers and composites), adhesive bonding, and other advanced joining methods (friction staking, laser welding, induction welding, etc.). Provides a combined engineering and scientific approach used to describe principles, properties, and applications of polymer-metal hybrid joints Describes the current developments in design of experiments and statistical analysis in joining technology with emphasis on joining of polymer-metal hybrid structures Covers recent innovations in joining technology of polymer-metal hybrid joints including friction riveting, friction spot joining, friction staking, and ultrasonic joining Principles illustrated by pictures, 3D-schemes, charts, and drawings using examples from the field of polymer-metal joining Joining of Polymer-Metal Hybrid Structures: Principles and Applications will appeal to chemical, polymer, materials, metallurgical, composites, mechanical, process, product, and welding engineers, scientists and students, technicians, and joining process professionals.
Download or read book Automotive Application of Polymers II written by A.N.A. Elliott and published by iSmithers Rapra Publishing. This book was released on 1991-12 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Rapra Review Report looks at the major applications of polymers in automotives, (excluding tyres), and describes the reasons behind their adoption and development, with many examples drawn from the European, US and Japanese car industries. The review and the 395 abstracts provided from the Rapra Polymer Library database refer primarily to developments since 1987.
Download or read book Atmospheric Pressure Plasma Treatment of Polymers written by Michael Thomas and published by John Wiley & Sons. This book was released on 2013-06-19 with total page 435 pages. Available in PDF, EPUB and Kindle. Book excerpt: An indispensable volume detailing the current and potential applications of atmospheric pressure plasma treatment by experts practicing in fields around the world Polymers are used in a wide variety of industries to fabricate legions of products because of their many desirable traits. However, polymers in general (and polyolefins, in particular) are innately not very adhesionable because of the absence of polar or reactive groups on their surfaces and concomitant low surface energy. Surface treatment of polymers, however, is essential to impart reactive chemical groups on their surfaces to enhance their adhesion characteristic. Proper surface treatment can endow polymers with improved adhesion without affecting the bulk properties. A plethora of techniques (ranging from wet to dry, simple to sophisticated, vacuum to non-vacuum) for polymer surface modification have been documented in the literature but the Atmospheric Pressure Plasma (APP) treatment has attracted much attention because it offers many advantages vis-a-vis other techniques, namely uniform treatment, continuous operation, no need for vacuum, simplicity, low cost, no environmental or disposal concern, and applicability to large area samples. Although the emphasis in this book is on the utility of APP treatment for enhancement of polymer adhesion, APP is also applicable and effective to modulate many other surface properties of polymers: superhydrophilicity, superhydrophobicity, anti-fouling, anti-fogging, anti-icing, cell adhesion, biocompatibility, tribological behavior, etc. The key features of Atmospheric Pressure Plasma Treatment of Polymers: Address design and functions of various types of reactors Bring out current and potential applications of APP treatment Represent the cumulative wisdom of many key academic and industry researchers actively engaged in this key and enabling technology
Download or read book Adhesive Bonding written by Walter Brockmann and published by John Wiley & Sons. This book was released on 2009-01-07 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: Both solid knowledge of the basics as well as expert knowledge is needed to create rigid, long-lasting and material-specific adhesions in the industrial or trade sectors. Information that is extremely difficult and time-consuming to find in the current literature. Written by specialists in various disciplines from both academia and industry, this handbook is the very first to provide such comprehensive knowledge in a compact and well-structured form. Alongside such traditional fields as the properties, chemistry and characteristic behavior of adhesives and adhesive joints, it also treats in detail current practical questions and the manifold applications for adhesives.
Download or read book Adhesives and Adhesive Bonding for Automotive Applications written by Materials Information Editors and published by . This book was released on 2004-01-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced Composite Materials for Automotive Applications written by Ahmed Elmarakbi and published by John Wiley & Sons. This book was released on 2013-10-09 with total page 487 pages. Available in PDF, EPUB and Kindle. Book excerpt: The automotive industry faces many challenges, including increased global competition, the need for higher-performance vehicles, a reduction in costs and tighter environmental and safety requirements. The materials used in automotive engineering play key roles in overcoming these issues: ultimately lighter materials mean lighter vehicles and lower emissions. Composites are being used increasingly in the automotive industry due to their strength, quality and light weight. Advanced Composite Materials for Automotive Applications: Structural Integrity and Crashworthiness provides a comprehensive explanation of how advanced composite materials, including FRPs, reinforced thermoplastics, carbon-based composites and many others, are designed, processed and utilized in vehicles. It includes technical explanations of composite materials in vehicle design and analysis and covers all phases of composite design, modelling, testing and failure analysis. It also sheds light on the performance of existing materials including carbon composites and future developments in automotive material technology which work towards reducing the weight of the vehicle structure. Key features: Chapters written by world-renowned authors and experts in their own fields Includes detailed case studies and examples covering all aspects of composite materials and their application in the automotive industries Unique topic integration between the impact, crash, failure, damage, analysis and modelling of composites Presents the state of the art in composite materials and their application in the automotive industry Integrates theory and practice in the fields of composite materials and automotive engineering Considers energy efficiency and environmental implications Advanced Composite Materials for Automotive Applications: Structural Integrity and Crashworthiness is a comprehensive reference for those working with composite materials in both academia and industry, and is also a useful source of information for those considering using composites in automotive applications in the future.
Download or read book Commercialization of New Manufacturing Processes for Materials Staff Research Study 22 written by and published by DIANE Publishing. This book was released on with total page 163 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Department of the Interior and Related Agencies Appropriations for 1996 written by United States. Congress. House. Committee on Appropriations. Subcommittee on Department of the Interior and Related Agencies and published by . This book was released on 1995 with total page 1494 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Commercialization of New Manufacturing Processes for Materials written by and published by . This book was released on 1998 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Surface Treatment of Materials for Adhesive Bonding written by Sina Ebnesajjad and published by William Andrew. This book was released on 2013-10-22 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aimed at engineers and materials scientists in a wide range of sectors, this book is a unique source of surface preparation principles and techniques for plastics, thermosets, elastomers, ceramics and metals bonding. With emphasis on the practical, it draws together the technical principles of surface science and surface treatments technologies to enable practitioners to improve existing surface preparation processes to improve adhesion and, as a result, enhance product life. This book describes and illustrates the surface preparations and operations that must be applied to a surface before acceptable adhesive bonding is achieved. It is meant to be an exhaustive overview, including more detailed explanation where necessary, in a continuous and logical progression. The book provides a necessary grounding in the science and practice of adhesion, without which adequate surface preparation is impossible. Surface characterization techniques are included, as is an up-to-date assessment of existing surface treatment technologies such as Atmospheric Plasma, Degreasing, Grit blasting, laser ablation and more. Fundamental material considerations are prioritised over specific applications, making this book relevant to all industries using adhesives, such as medical, automotive, aerospace, packaging and electronics. This second edition represents a full and detailed update, with all major developments in the field included and three chapters added to cover ceramic surface treatment, plasma treatment of non-metallic materials, and the effect of additives on surface properties of plastics. - A vital resource for improving existing surface treatment processes to increase product life by creating stronger, more durable adhesive bonds - Relevant across a variety of industries, including medical, automotive and packaging - Provides essential grounding in the science of surface adhesion, and details how this links with the practice of surface treatment
Download or read book Industry Trade and Technology Review written by and published by . This book was released on 1997 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Bonding Elastomers written by G. Polaski and published by iSmithers Rapra Publishing. This book was released on 2005 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: This review has been written as a practical approach to bonding various kinds of elastomers to substrates such as steel and plastics, as used in the manufacture of diverse products such as rubber covered rolls, urethane fork lift wheels, rubber lining for chemical storage or solid rocket motors, engine bushes and mounts, seals for transmissions, electrical power connectors and military tank track pads. Based on the authors' years of experience working closely with end-use customers and it offers a thorough overview of how to successfully bond rubber to a given substrate in the manufacture of quality rubber engineered components. This review is supported by an indexed section containing several hundred key references and abstracts selected from the Rapra Abstracts database.
Download or read book Handbook of Adhesion Technology written by Lucas F. M. da Silva and published by Springer Science & Business Media. This book was released on 2011-06-10 with total page 1569 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adhesives have been used for thousands of years, but until 100 years ago, the vast majority was from natural products such as bones, skins, fish, milk, and plants. Since about 1900, adhesives based on synthetic polymers have been introduced, and today, there are many industrial uses of adhesives and sealants. It is difficult to imagine a product—in the home, in industry, in transportation, or anywhere else for that matter—that does not use adhesives or sealants in some manner. The Handbook of Adhesion Technology is intended to be the definitive reference in the field of adhesion. Essential information is provided for all those concerned with the adhesion phenomenon. Adhesion is a phenomenon of interest in diverse scientific disciplines and of importance in a wide range of technologies. Therefore, this handbook includes the background science (physics, chemistry and materials science), engineering aspects of adhesion and industry specific applications. It is arranged in a user-friendly format with ten main sections: theory of adhesion, surface treatments, adhesive and sealant materials, testing of adhesive properties, joint design, durability, manufacture, quality control, applications and emerging areas. Each section contains about five chapters written by internationally renowned authors who are authorities in their fields. This book is intended to be a reference for people needing a quick, but authoritative, description of topics in the field of adhesion and the practical use of adhesives and sealants. Scientists and engineers of many different backgrounds who need to have an understanding of various aspects of adhesion technology will find it highly valuable. These will include those working in research or design, as well as others involved with marketing services. Graduate students in materials, processes and manufacturing will also want to consult it.
