Download or read book Active Control of Fan Noise Feasibility Study written by and published by . This book was released on 1996 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Active Control of Fan Noise written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-02 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes the Active Noise Cancellation (ANC) System designed by General Electric and tested in the NASA Lewis Research Center's (LERC) 48 inch Active Noise Control Fan (ANCF). The goal of this study is to assess the feasibility of using wall mounted secondary acoustic sources and sensors within the duct of a high bypass turbofan aircraft engine for global active noise cancellation of fan tones. The GE ANC system is based on a modal control approach. A known acoustic mode propagating in the fan duct is canceled using an array of flush-mounted compact sound sources. The canceling modal signal is generated by a modal controller. Inputs to the controller are signals from a shaft encoder and from a microphone array which senses the residual acoustic mode in the duct. The key results are that the (6,0) was completely eliminated at the 920 Hz design frequency and substantially reduced elsewhere. The total tone power was reduced 6.8 dB (out of a possible 9.8 dB). Farfield reductions of 15 dB (SPL) were obtained. The (4,0) and (4,1) modes were reduced simultaneously yielding a 15 dB PWL decrease. The results indicate that global attenuation of PWL at the target frequency was obtained in the aft quadrant using an ANC actuator and sensor system totally contained within the duct. The quality of the results depended on precise mode generation. High spillover into spurious modes generated by the ANC actuator array caused less than optimum levels of PWL reduction. The variation in spillover is believed to be due to calibration procedure, but must be confirmed in subsequent tests. Pla, Frederic G. and Hu, Ziqiang and Sutliff, Daniel L. Glenn Research Center...
Download or read book Active Control of Fan Noise Feasibility Study written by and published by . This book was released on 1996 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Active Control of Fan generated Plane Wave Noise written by and published by . This book was released on 1993 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Active Control of Fan Noise by Vane Actuators written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-08-27 with total page 94 pages. Available in PDF, EPUB and Kindle. Book excerpt: An active noise control system for ducted fan noise was built that uses actuators located in stator vanes. The actuators were piezoelectric benders manufactured using the THUNDER technology and were custom designed for the application. The active noise control system was installed in the NASA ANCF rig. Four actuator array with a total of 168 actuators in 28 stator vanes were used. Simultaneous reductions of acoustic power in both the inlet and exhaust duct were demonstrated for a fan disturbance that contained two radial mode orders in both inlet and exhaust. Total power levels in the target modes were reduced by up to 9 dB in the inlet and total tone levels by over 6 dB while exhaust power levels were reduced by up to 3 dB. Far field sound pressure level reductions of up to 17 dB were observed. A simpler control system, matched to the location of the disturbance with two radial actuator arrays, was demonstrated to control total acoustic power in four disturbance modes simultaneously in inlet and exhaust. The vane actuator met the requirements given for the ANCF, although in practice the performance of the system was limited by the constraints of the power amplifiers and the presence of control spillover. The vane actuators were robust. None of the 168 vane actuators failed during the tests.Curtis, Alan R. D.Glenn Research Center; Langley Research CenterACTIVE CONTROL; AERODYNAMIC NOISE; NOISE REDUCTION; PIEZOELECTRICITY; SOUND PRESSURE; ACTUATORS; FAR FIELDS; STATORS...
Download or read book Active Control of Fan Noise by Vane Actuators written by and published by . This book was released on 1999 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Active Control of Fan Noise feasibility Study Volume 2 Canceling Noise Source design of an Acoustic Plate Radiator Using Piezoceramic Actuators written by and published by . This book was released on 1995 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Active Control of Fan Generated Plane Wave Noise written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-30 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Subsonic propulsion systems for future aircraft may incorporate ultra-high bypass ratio ducted fan engines whose dominant noise source is the fan with blade passage frequency less than 1000 Hz. This low frequency combines with the requirement of a short nacelle to diminish the effectiveness of passive duct liners. Active noise control is seen as a viable method to augment the conventional passive treatments. An experiment to control ducted fan noise using a time domain active adaptive system is reported. The control sound source consists of loudspeakers arrayed around the fan duct. The error sensor location is in the fan duct. The purpose of this experiment is to demonstrate that the in-duct error sensor reduces the mode spillover in the far field, thereby increasing the efficiency of the control system. In this first series of tests, the fan is configured so that predominantly zero order circumferential waves are generated. The control system is found to reduce the blade passage frequency tone significantly in the acoustic far field when the mode orders of the noise source and of the control source are the same. The noise reduction is not as great when the mode orders are not the same even though the noise source modes are evanescent, but the control system converges stably and global noise reduction is demonstrated in the far field. Further experimentation is planned in which the performance of the system will be evaluated when higher order radial and spinning modes are generated. Gerhold, Carl H. and Nuckolls, William E. and Santamaria, Odillyn L. and Martinson, Scott D. Langley Research Center RTOP 535-03-11-02...
Download or read book Active Control of Fan Noise written by National Aeronautics and Space Adm Nasa and published by . This book was released on 2018-11 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this effort is to develop an analytical model for the coupling of active noise control (ANC) piston-type actuators that are mounted flush to the inner and outer walls of an annular duct to the modes in the duct generated by the actuator motion. The analysis will be used to couple the ANC actuators to the modal analysis propagation computer program for the annular duct, to predict the effects of active suppression of fan-generated engine noise sources. This combined program will then be available to assist in the design or evaluation of ANC systems in fan engine annular exhaust ducts. An analysis has been developed to predict the modes generated in an annular duct due to the coupling of flush-mounted ring actuators on the inner and outer walls of the duct. The analysis has been combined with a previous analysis for the coupling of modes to a cylindrical duct in a FORTRAN computer program to perform the computations. The method includes the effects of uniform mean flow in the duct. The program can be used for design or evaluation purposes for active noise control hardware for turbofan engines. Predictions for some sample cases modeled after the geometry of the NASA Lewis ANC Fan indicate very efficient coupling in both the inlet and exhaust ducts for the m = 6 spinning mode at frequencies where only a single radial mode is cut-on. Radial mode content in higher order cut-off modes at the source plane and the required actuator displacement amplitude to achieve 110 dB SPL levels in the desired mode were predicted. Equivalent cases with and without flow were examined for the cylindrical and annular geometry, and little difference was found for a duct flow Mach number of 0.1. The actuator ring coupling program will be adapted as a subroutine to the cylindrical duct modal analysis and the exhaust duct modal analysis. This will allow the fan source to be defined in terms of characteristic modes at the fan source plane and predict the propagation to the arbit...
Download or read book Active Control of Fan Noise written by National Aeronautics and Space Adm Nasa and published by . This book was released on 2018-10-22 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: A computational method to predict modal reflection coefficients in cylindrical ducts has been developed based on the work of Homicz, Lordi, and Rehm, which uses the Wiener-Hopf method to account for the boundary conditions at the termination of a thin cylindrical pipe. The purpose of this study is to develop a computational routine to predict the reflection coefficients of higher order acoustic modes impinging on the unflanged termination of a cylindrical duct. This effort was conducted wider Task Order 5 of the NASA Lewis LET Program, Active Noise Control of aircraft Engines: Feasibility Study, and will be used as part of the development of an integrated source noise, acoustic propagation, ANC actuator coupling, and control system algorithm simulation. The reflection coefficient prediction will be incorporated into an existing cylindrical duct modal analysis to account for the reflection of modes from the duct termination. This will provide a more accurate, rapid computation design tool for evaluating the effect of reflected waves on active noise control systems mounted in the duct, as well as providing a tool for the design of acoustic treatment in inlet ducts. As an active noise control system design tool, the method can be used preliminary to more accurate but more numerically intensive acoustic propagation models such as finite element methods. The resulting computer program has been shown to give reasonable results, some examples of which are presented. Reliable data to use for comparison is scarce, so complete checkout is difficult, and further checkout is needed over a wider range of system parameters. In future efforts the method will be adapted as a subroutine to the GEAE segmented cylindrical duct modal analysis program. Kraft, R. E. Unspecified Center NAS3-26617; RTOP 538-03-11...
Download or read book Active Control of Fan Noise in Ducts Using Magnetic Bearings written by Jonathan Philip Nelson and published by . This book was released on 2002 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this project was to investigate global noise attenuation of narrow band fan noise in an air duct through the use of magnetic bearings. An axial flow fan creates tonal noise related to its rotational rate. Additional noise exists due to harmonics of this frequency as well as turbulent airflow. In addition to conventional brush bearings to support the fan shaft radially, this project used an active magnetic thrust bearing to control axial movement. The thrust bearing primarily functioned as an active sound control actuator. Active sound control is the method of achieving destructive interference of sound waves by outputting a secondary wave of equal amplitude and frequency, but 180 degrees out of phase with the primary wave. An error microphone was positioned in the duct to provide feedback to a Digital Signal Processor (DSP), which contained the active sound control program, while a performance microphone tested for global sound control at various points along the duct. Instead of using a secondary speaker, this project used the fan itself to collate the primary and secondary sound sources. Therefore, global sound control throughout the duct was theoretically possible. This project demonstrated this global control of noise experimentally.
Download or read book Active Control of Fan Noise written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-30 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this effort is to develop an analytical model for the coupling of active noise control (ANC) piston-type actuators that are mounted flush to the inner and outer walls of an annular duct to the modes in the duct generated by the actuator motion. The analysis will be used to couple the ANC actuators to the modal analysis propagation computer program for the annular duct, to predict the effects of active suppression of fan-generated engine noise sources. This combined program will then be available to assist in the design or evaluation of ANC systems in fan engine annular exhaust ducts. An analysis has been developed to predict the modes generated in an annular duct due to the coupling of flush-mounted ring actuators on the inner and outer walls of the duct. The analysis has been combined with a previous analysis for the coupling of modes to a cylindrical duct in a FORTRAN computer program to perform the computations. The method includes the effects of uniform mean flow in the duct. The program can be used for design or evaluation purposes for active noise control hardware for turbofan engines. Predictions for some sample cases modeled after the geometry of the NASA Lewis ANC Fan indicate very efficient coupling in both the inlet and exhaust ducts for the m = 6 spinning mode at frequencies where only a single radial mode is cut-on. Radial mode content in higher order cut-off modes at the source plane and the required actuator displacement amplitude to achieve 110 dB SPL levels in the desired mode were predicted. Equivalent cases with and without flow were examined for the cylindrical and annular geometry, and little difference was found for a duct flow Mach number of 0.1. The actuator ring coupling program will be adapted as a subroutine to the cylindrical duct modal analysis and the exhaust duct modal analysis. This will allow the fan source to be defined in terms of characteristic modes at the fan source plane and predict the propagation to the arbit...
Download or read book Active Control of Fan Noise written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-30 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt: A computational method to predict modal reflection coefficients in cylindrical ducts has been developed based on the work of Homicz, Lordi, and Rehm, which uses the Wiener-Hopf method to account for the boundary conditions at the termination of a thin cylindrical pipe. The purpose of this study is to develop a computational routine to predict the reflection coefficients of higher order acoustic modes impinging on the unflanged termination of a cylindrical duct. This effort was conducted wider Task Order 5 of the NASA Lewis LET Program, Active Noise Control of aircraft Engines: Feasibility Study, and will be used as part of the development of an integrated source noise, acoustic propagation, ANC actuator coupling, and control system algorithm simulation. The reflection coefficient prediction will be incorporated into an existing cylindrical duct modal analysis to account for the reflection of modes from the duct termination. This will provide a more accurate, rapid computation design tool for evaluating the effect of reflected waves on active noise control systems mounted in the duct, as well as providing a tool for the design of acoustic treatment in inlet ducts. As an active noise control system design tool, the method can be used preliminary to more accurate but more numerically intensive acoustic propagation models such as finite element methods. The resulting computer program has been shown to give reasonable results, some examples of which are presented. Reliable data to use for comparison is scarce, so complete checkout is difficult, and further checkout is needed over a wider range of system parameters. In future efforts the method will be adapted as a subroutine to the GEAE segmented cylindrical duct modal analysis program. Kraft, R. E. Unspecified Center NAS3-26617; RTOP 538-03-11...
Download or read book Optimization of Active Noise Control for Small Axial Cooling Fans written by Brian B. Monson and published by . This book was released on 2006 with total page 63 pages. Available in PDF, EPUB and Kindle. Book excerpt: Previous work has shown that active noise control is a feasible solution to attenuate tonal noise radiated by small axial cooling fans, such as those found in desktop computers. One such control system reduced noise levels of a baffled 80-mm fan in the free field with four small loudspeakers surrounding the fan. Due to industry specified spatial constraints, a smaller fan and speaker configuration was desirable. The smaller configuration maintains similar control performance, further facilitating practical implementation of the control system. The smaller control system employs a smaller fan running at a higher speed. Different loudspeaker configurations for control exist and have been tested. A configuration consisting of four control sources spaced symmetrically around and coplanar to the fan exhibits global control of the tonal component of the fan noise. A configuration with three symmetrically spaced sources is shown to perform similarly, agreeing with theoretical prediction. An analysis of the control system in a non-ideal reflective environment is also discussed.
Download or read book Active Control of Noise and Vibration written by Colin Hansen and published by CRC Press. This book was released on 2012-11-02 with total page 1564 pages. Available in PDF, EPUB and Kindle. Book excerpt: Integrating active control of both sound and vibration, this comprehensive two-volume set combines coverage of fundamental principles with the most recent theoretical and practical developments. The authors explain how to design and implement successful active control systems in practice and detail the pitfalls one must avoid to ensure a reliable and stable system. Extensively revised, updated, and expanded throughout, the second edition reflects the advances that have been made in algorithms, DSP hardware, and applications since the publication of the first edition.
Download or read book Active Control of Fan Noise written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-28 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt: An extension of a prior study has been completed to examine the potential reduction of aircraft flyover noise by the method of active noise control (ANC). It is assumed that the ANC system will be designed such that it cancels discrete tones radiating from the engine fan inlet or fan exhaust duct, at least to the extent that they no longer protrude above the surrounding broadband noise levels. Thus, without considering the engineering details of the ANC system design, tone levels am arbitrarily removed from the engine component noise spectrum and the flyover noise EPNL levels are compared with and without the presence of tones. The study was conducted for a range of engine cycles, corresponding to fan pressure ratios of 1.3, 1.45, 1.6, and 1.75. This report is an extension of an effort reported previously. The major conclusions drawn from the prior study, which was restricted to fan pressure ratios of 1.45 and 1.75, are that, for a fan pressure ratio of 1.75, ANC of tones gives about the same suppression as acoustic treatment without ANC. For a fan pressure ratio of 1.45, ANC appears to offer less effectiveness from passive treatment. In the present study, the other two fan pressure ratios are included in a more detailed examination of the benefits of the ANC suppression levels. The key results of this extended study are the following observations: (1) The maximum overall benefit obtained from suppression of BPF alone was 2.5 EPNdB at high fan speeds. The suppression benefit increases with increase in fan pressure ratio (FPR), (2) The maximum overall benefit obtained from suppression of the first three harmonics was 3 EPNdB at high speeds. Suppression benefit increases with increase in FPR, (3) At low FPR, only about 1.0 EPNdB maximum reduction was obtained. Suppression is primarily from reduction of BPF at high FPR values and from the combination of tones at low FPR, (4) The benefit from ANC is about the same as the benefit from passive treatment at fan pressure ra...
Download or read book Active Noise Control of Low Speed Fan Rotor Stator Modes written by and published by . This book was released on 1996 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:
