Download or read book A Sand Plasticity Model for Earthquake Engineering Applications written by Aikaterini Ziotopoulou and published by . This book was released on 2014 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The development of the sand plasticity model PM4Sand (Versions 2 and 3) for geotechnical earthquake engineering applications is presented. The motivation behind this work is twofold. The first goal is to have a constitutive model that is applicable to the wide range of conditions encountered in geotechnical engineering practice, is easy to calibrate utilizing the limited data that are usually available and can reasonably approximate the behaviors of interest. The second goal is to provide an extensive documentation of the capabilities and limitations of the model. The PM4Sand plasticity model is built upon the basic framework of the stress-ratio controlled, critical state compatible, bounding surface plasticity model for sand presented by Dafalias and Manzari (2004). A series of modifications and additions to the model were incorporated by Boulanger (2010; Version 1) and further herein (Version 2 and Version 3) to improve its ability to approximate the stress-strain responses important to geotechnical earthquake engineering practice; in essence, the model is calibrated at the equation level to provide for better approximation of the trends observed in empirical correlations commonly used in practice. Each stage of its development has been guided by consecutive cycles of formulation, validation and calibration against the whole body of available data (case histories, lab, centrifuge and shake table tests) on the cyclic behavior of sands both at the element and at the system level. The formulation of PM4Sand Version 2 for geotechnical earthquake engineering applications is presented followed by its calibration and implementation. A generalized calibration of the constitutive model is presented which attempts to produce drained and undrained, monotonic and cyclic responses under a broad range of stress conditions that are reasonably consistent with the behaviors expected based on engineering correlations to commonly available in-situ test data (i.e., SPT, CPT and Vs data). Simulated single element responses are compared to design correlations to illustrate the efficacy of the model modifications and evaluate the model’s performance. The constitutive model is shown to be relatively easy to calibrate and provide reasonable responses for key liquefaction behaviors. The numerical implementation as a user defined material for use in a two-dimensional explicit finite difference program is described. The formulation of PM4Sand Version 3 for improved modeling of post-liquefaction reconsolidation strains is presented. Modifications are introduced that provide a means for improved modeling of post-liquefaction reconsolidation strains after the end of strong shaking in a nonlinear deformation analysis. The methodology of the approach along with the calibration is presented, followed by a comparison of the response computed for a field case history. A review is presented on the performance of a number of constitutive models in reasonably predicting liquefaction effects under sloping ground conditions. Example results from undrained cyclic DSS tests on clean sands under zero and nonzero static shear stress ratio conditions are presented and findings from past experimental studies for these types of loading conditions are reviewed. Examples are presented of the performance of selected constitutive models in modeling the observed experimental results. It is shown that they all have certain limitations and that the effect of sloping ground conditions is particularly difficult to simulate. Finally, the formulation of PM4Sand Version 3 is further updated to better account for the effects of sloping ground conditions and irregular cyclic loading on liquefaction behaviors and thus improve simulations of liquefaction-induced deformations of sloping ground. Existing laboratory test data are reviewed and new experimental data from undrained cyclic Direct Simple Shear (DSS) lab tests of liquefiable sand under sloping ground conditions subjected to irregular cyclic loading are introduced. Evidence from the tests shows that it is the effect of loading history on the dilatancy and stiffness characteristics of the response that is not properly captured by the model. The modifications made in Version 3 include a revised dependency of dilatancy and plastic modulus on the fabric tensor and its history. These modifications are introduced using the irregular cyclic DSS testing to illustrate the motivations for the changes in the constitutive equations. Finally, two examples of calibration are presented: one against a specific lab test result for a single sand and one against an engineering correlation describing trends observed for many sands across a broader range of relative densities, confining stresses, and loading conditions. The updated formulation in Version 3 of the model is shown to better approximate liquefaction behaviors for sloping ground conditions.

Download or read book Earthquake Geotechnical Engineering for Protection and Development of Environment and Constructions written by Francesco Silvestri and published by CRC Press. This book was released on 2019-10-22 with total page 5946 pages. Available in PDF, EPUB and Kindle. Book excerpt: Earthquake Geotechnical Engineering for Protection and Development of Environment and Constructions contains invited, keynote and theme lectures and regular papers presented at the 7th International Conference on Earthquake Geotechnical Engineering (Rome, Italy, 17-20 June 2019. The contributions deal with recent developments and advancements as well as case histories, field monitoring, experimental characterization, physical and analytical modelling, and applications related to the variety of environmental phenomena induced by earthquakes in soils and their effects on engineered systems interacting with them. The book is divided in the sections below: Invited papers Keynote papers Theme lectures Special Session on Large Scale Testing Special Session on Liquefact Projects Special Session on Lessons learned from recent earthquakes Special Session on the Central Italy earthquake Regular papers Earthquake Geotechnical Engineering for Protection and Development of Environment and Constructions provides a significant up-to-date collection of recent experiences and developments, and aims at engineers, geologists and seismologists, consultants, public and private contractors, local national and international authorities, and to all those involved in research and practice related to Earthquake Geotechnical Engineering.

Download or read book Proceedings of the 4th International Conference on Performance Based Design in Earthquake Geotechnical Engineering Beijing 2022 written by Lanmin Wang and published by Springer Nature. This book was released on 2022-09-19 with total page 2417 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 4th International Conference on Performance-based Design in Earthquake Geotechnical Engineering (PBD-IV) is held in Beijing, China. The PBD-IV Conference is organized under the auspices of the International Society of Soil Mechanics and Geotechnical Engineering - Technical Committee TC203 on Earthquake Geotechnical Engineering and Associated Problems (ISSMGE-TC203). The PBD-I, PBD-II, and PBD-III events in Japan (2009), Italy (2012), and Canada (2017) respectively, were highly successful events for the international earthquake geotechnical engineering community. The PBD events have been excellent companions to the International Conference on Earthquake Geotechnical Engineering (ICEGE) series that TC203 has held in Japan (1995), Portugal (1999), USA (2004), Greece (2007), Chile (2011), New Zealand (2015), and Italy (2019). The goal of PBD-IV is to provide an open forum for delegates to interact with their international colleagues and advance performance-based design research and practices for earthquake geotechnical engineering.

Download or read book Proceedings of the Third International Conference on Sustainable Civil Engineering and Architecture written by J. N. Reddy and published by Springer Nature. This book was released on 2024-01-12 with total page 1973 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book includes articles from the Third International Conference on Sustainable Civil Engineering and Architecture (ICSSEA 2023), held at Da Nang City, Vietnam, on July 19-21, 2023. The conference brings together international experts from both academia and industry to share their knowledge and expertise, facilitate collaboration, and improve cooperation in the field. The book focuses on the most recent developments in sustainable architecture and civil engineering, including offshore structures, structural engineering, building materials, and architecture.

Download or read book Analytical Methods in Petroleum Upstream Applications written by Cesar Ovalles and published by CRC Press. This book was released on 2015-04-02 with total page 1351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Effective measurement of the composition and properties of petroleum is essential for its exploration, production, and refining; however, new technologies and methodologies are not adequately documented in much of the current literature. Analytical Methods in Petroleum Upstream Applications explores advances in the analytical methods and instrumentation that allow more accurate determination of the components, classes of compounds, properties, and features of petroleum and its fractions. Recognized experts explore a host of topics, including: A petroleum molecular composition continuity model as a context for other analytical measurements A modern modular sampling system for use in the lab or the process area to collect and control samples for subsequent analysis The importance of oil-in-water measurements and monitoring The chemical and physical properties of heavy oils, their fractions, and products from their upgrading Analytical measurements using gas chromatography and nuclear magnetic resonance (NMR) applications Asphaltene and heavy ends analysis Chemometrics and modeling approaches for understanding petroleum composition and properties to improve upstream, midstream, and downstream operations Due to the renaissance of gas and oil production in North America, interest has grown in analytical methods for a wide range of applications. The understanding provided in this text is designed to help chemists, geologists, and chemical and petroleum engineers make more accurate estimates of the crude value to specific refinery configurations, providing insight into optimum development and extraction schemes.

Download or read book Proceedings of 17th Symposium on Earthquake Engineering Vol 3 written by Manish Shrikhande and published by Springer Nature. This book was released on 2023-07-03 with total page 763 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents select proceedings of the 17th Symposium on Earthquake Engineering organized by the Department of Earthquake Engineering, Indian Institute of Technology Roorkee. The topics covered in the proceedings include engineering seismology and seismotectonics, earthquake hazard assessment, seismic microzonation and urban planning, dynamic properties of soils and ground response, ground improvement techniques for seismic hazards, computational soil dynamics, dynamic soil–structure interaction, codal provisions on earthquake-resistant design, seismic evaluation and retrofitting of structures, earthquake disaster mitigation and management, and many more. This book also discusses relevant issues related to earthquakes, such as human response and socioeconomic matters, post-earthquake rehabilitation, earthquake engineering education, public awareness, participation and enforcement of building safety laws, and earthquake prediction and early warning system. This book is a valuable reference for researchers and professionals working in the area of earthquake engineering.

Download or read book Cone Penetration Testing 2022 written by Guido Gottardi and published by CRC Press. This book was released on 2022-06-24 with total page 2767 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains the proceedings of the 5th International Symposium on Cone Penetration Testing (CPT’22), held in Bologna, Italy, 8-10 June 2022. More than 500 authors - academics, researchers, practitioners and manufacturers – contributed to the peer-reviewed papers included in this book, which includes three keynote lectures, four invited lectures and 169 technical papers. The contributions provide a full picture of the current knowledge and major trends in CPT research and development, with respect to innovations in instrumentation, latest advances in data interpretation, and emerging fields of CPT application. The paper topics encompass three well-established topic categories typically addressed in CPT events: - Equipment and Procedures - Data Interpretation - Applications. Emphasis is placed on the use of statistical approaches and innovative numerical strategies for CPT data interpretation, liquefaction studies, application of CPT to offshore engineering, comparative studies between CPT and other in-situ tests. Cone Penetration Testing 2022 contains a wealth of information that could be useful for researchers, practitioners and all those working in the broad and dynamic field of cone penetration testing.

Download or read book Model Tests and Numerical Simulations of Liquefaction and Lateral Spreading written by Bruce L. Kutter and published by Springer Nature. This book was released on 2019-01-01 with total page 660 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book presents work collected through the Liquefaction Experiments and Analysis Projects (LEAP) in 2017. It addresses the repeatability, variability, and sensitivity of lateral spreading observed in twenty-four centrifuge model tests on mildly sloping liquefiable sand. The centrifuge tests were conducted at nine different centrifuge facilities around the world. For the first time, a sufficient number of experiments were conducted to enable assessment of variability of centrifuge test results. The experimental data provided a unique basis for assessing the capabilities of twelve different simulation platforms for numerical simulation of soil liquefaction. The results of the experiments and the numerical simulations are presented and discussed in papers submitted by the project participants. The work presented in this book was followed by LEAP-Asia that included assessment of a generalized scaling law and culminated in a workshop in Osaka, Japan in March 2019. LEAP-2020, ongoing at the time of printing, is addressing the validation of soil-structure interaction analyses of retaining walls involving a liquefiable soil. A workshop is planned at RPI, USA in 2020. .

Download or read book Perspectives on Earthquake Geotechnical Engineering written by Atilla Ansal and published by Springer. This book was released on 2015-04-15 with total page 484 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers a broad perspective on important topics in earthquake geotechnical engineering and gives specialists and those that are involved with research and application a more comprehensive understanding about the various topics. Consisting of eighteen chapters written by authors from the most seismic active regions of the world, such as USA, Japan, Canada, Chile, Italy, Greece, Portugal, Taiwan, and Turkey, the book reflects different views concerning how to assess and minimize earthquake damage. The authors, a prominent group of specialists in the field of earthquake geotechnical engineering, are the invited lecturers of the International Conference on Earthquake Geotechnical Engineering from Case History to Practice in the honour of Professor Kenji Ishihara held in Istanbul, Turkey during 17-19 June 2013.

Download or read book Advances in Computer Methods and Geomechanics written by Amit Prashant and published by Springer Nature. This book was released on 2020-03-11 with total page 716 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents selected papers from IACMAG Symposium,The major themes covered in this conference are Earthquake Engineering, Ground Improvement and Constitutive Modelling. This volume will be of interest to researchers and practitioners in geotechnical and geomechanical engineering.

Download or read book From Research to Applied Geotechnics written by N.P. López-Acosta and published by IOS Press. This book was released on 2019-11-26 with total page 458 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first Pan-American Conference on Soil Mechanics and Geotechnical Engineering (PCSMGE) was held in Mexico in 1959. Every 4 years since then, PCSMGE has brought together the geotechnical engineering community from all over the world to discuss the problems, solutions and future challenges facing this engineering sector. Sixty years after the first conference, the 2019 edition returns to Mexico. The XVI PCSMGE 2019 conference was held in Cancun, Mexico, from 17 – 20 November 2019. This book presents the plenary lectures from the conference, delivered by distinguished geotechnical engineers of international renown. Experience and youth combine in this special publication, which includes the 9th Arthur Casagrande lecture, the plenary lecture of the ISSMGE President, 3 Bright Spark lectures, and the manuscripts of the 13 invited lecturers of practically all the technical sessions at the XVI PCSMGE 2019. Topics cover both research and applied geotechnics, including recent developments in geotechnical engineering. Representing a valuable reference for engineering practitioners and graduate students, and helping to identify new issues and shape future directions for research, the book will be of interest to all those working in the field, involved in soil mechanics and geotechnical engineering.

Download or read book Model Tests and Numerical Simulations of Liquefaction and Lateral Spreading II written by Tetsuo Tobita and published by Springer Nature. This book was released on with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Safety and Reliability Methodology and Applications written by Tomasz Nowakowski and published by CRC Press. This book was released on 2014-09-18 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Within the last fifty years the performance requirements for technical objects and systems were supplemented with: customer expectations (quality), abilities to prevent the loss of the object properties in operation time (reliability and maintainability), protection against the effects of undesirable events (safety and security) and the ability to restore performance (resilience). The need to adapt the operation of complex systems in such an uncertain and volatile environment has caused the necessity to formulate new and well established achievements associated with modeling, testing and evaluation of these properties. The concept of a complex system applies not only to the technical ones but also the infrastructure of major importance for social life such as transportation and logistics systems, buildings, power systems, water distribution systems or health services. Safety and Reliability: Methodology and Applications contains the proceedings of the 24th European Safety and Reliability Conference (ESREL 2014, Wroclaw, Poland, 14-18 September 2014), and discusses theories and methods and their applications in the areas of risk, safety and reliability. The abstracts book (408 pages) + full paper CD-ROM (2496 pages) will be of interest to researchers and practitioners, academics and engineers working in academic, industrial and governmental sectors.

Download or read book Numerical Methods in Geotechnical Engineering IX written by António S. Cardoso and published by CRC Press. This book was released on 2018-06-19 with total page 1656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Numerical Methods in Geotechnical Engineering IX contains 204 technical and scientific papers presented at the 9th European Conference on Numerical Methods in Geotechnical Engineering (NUMGE2018, Porto, Portugal, 25—27 June 2018). The papers cover a wide range of topics in the field of computational geotechnics, providing an overview of recent developments on scientific achievements, innovations and engineering applications related to or employing numerical methods. They deal with subjects from emerging research to engineering practice, and are grouped under the following themes: Constitutive modelling and numerical implementation Finite element, discrete element and other numerical methods. Coupling of diverse methods Reliability and probability analysis Large deformation – large strain analysis Artificial intelligence and neural networks Ground flow, thermal and coupled analysis Earthquake engineering, soil dynamics and soil-structure interactions Rock mechanics Application of numerical methods in the context of the Eurocodes Shallow and deep foundations Slopes and cuts Supported excavations and retaining walls Embankments and dams Tunnels and caverns (and pipelines) Ground improvement and reinforcement Offshore geotechnical engineering Propagation of vibrations Following the objectives of previous eight thematic conferences, (1986 Stuttgart, Germany; 1990 Santander, Spain; 1994 Manchester, United Kingdom; 1998 Udine, Italy; 2002 Paris, France; 2006 Graz, Austria; 2010 Trondheim, Norway; 2014 Delft, The Netherlands), Numerical Methods in Geotechnical Engineering IX updates the state-of-the-art regarding the application of numerical methods in geotechnics, both in a scientific perspective and in what concerns its application for solving practical boundary value problems. The book will be much of interest to engineers, academics and professionals involved or interested in Geotechnical Engineering.

Download or read book Proceedings of GeoShanghai 2018 International Conference Fundamentals of Soil Behaviours written by Annan Zhou and published by Springer. This book was released on 2018-05-10 with total page 1026 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the second volume of the proceedings of the 4th GeoShanghai International Conference that was held on May 27 - 30, 2018. The book, entitled “Fundamentals of Soil Behaviours”, presents the recent advances and technology in the understanding and modelling of fundamentals of soil’s behaviours. The subject of this book covers a wide range of topics related to soil behaviours in geotechnical engineering, geoenvironmental engineering and transportation engineering. The state-of-the-art theories, methodologies and findings in the related topics are included. This book may benefit researchers and scientists from the academic fields of soil and rock mechanics, geotechnical engineering, geoenvironmental engineering, transportation engineering, geology, mining and energy, as well as practical engineers from industry. Each of the papers included in this book received at least two positive peer reviews. The editors would like to express their sincerest appreciation to all of the anonymous reviewers all over the world, for their diligent work.

Download or read book Modeling in Geotechnical Engineering written by Pijush Samui and published by Academic Press. This book was released on 2020-12-01 with total page 518 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modeling in Geotechnical Engineering is a one stop reference for a range of computational models, the theory explaining how they work, and case studies describing how to apply them. Drawing on the expertise of contributors from a range of disciplines including geomechanics, optimization, and computational engineering, this book provides an interdisciplinary guide to this subject which is suitable for readers from a range of backgrounds. Before tackling the computational approaches, a theoretical understanding of the physical systems is provided that helps readers to fully grasp the significance of the numerical methods. The various models are presented in detail, and advice is provided on how to select the correct model for your application. - Provides detailed descriptions of different computational modelling methods for geotechnical applications, including the finite element method, the finite difference method, and the boundary element method - Gives readers the latest advice on the use of big data analytics and artificial intelligence in geotechnical engineering - Includes case studies to help readers apply the methods described in their own work

Download or read book Numerical Methods in Geotechnical Engineering IX Volume 1 written by Manuel de Matos Fernandes and published by CRC Press. This book was released on 2018-06-22 with total page 935 pages. Available in PDF, EPUB and Kindle. Book excerpt: NUMGE 2018 is the ninth in a series of conferences on Numerical Methods in Geotechnical Engineering organized by the ERTC7 under the auspices of the International Society for Soil Mechanics and Geotechnical Engineering (ISSMGE). The first conference was held in 1986 in Stuttgart, Germany and the series continued every four years (1990 Santander, Spain; 1994 Manchester, United Kingdom; 1998 Udine, Italy; 2002 Paris, France; 2006 Graz, Austria; 2010 Trondheim, Norway; 2014 Delft, The Netherlands). The conference provides a forum for exchange of ideas and discussion on topics related to numerical modelling in geotechnical engineering. Both senior and young researchers, as well as scientists and engineers from Europe and overseas, are invited to attend this conference to share and exchange their knowledge and experiences. This work is the first volume of NUMGE 2018.