Download or read book A New Trend in Designing Plant Layouts for the Process Industry written by Richart Vazquez-Roman and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The numerical difficulty of solving the layout problem even without toxic release has been clearly identified in (Vázquez-Román et al., 2009). An example considers two new facilities and the control room to be installed in a given land where there exist two installed facilities. While applying several optimization methods and using different initializations, three optima results were found. It should then be clear than increasing the number of units may produce more local optima and the question would remain about what is the best layout. The global optimum for this case was obtained through a global optimizer in GAMS (Brooke et al., 1998), but the time required to achieve the solution is too high and this time became unpractical when the number of facilities was increased. To test the stochastic approach, a chlorine release was considered to occur in one of the installed facilities. All information required for the stochastic approach is provided in (Vázquez-Román et al., 2009). In this case two optimum layouts were detected with different GAMS solvers, Fig. 3. Though the global optimum was clearly identified, it was observed that it produced a small value in the cost associated to the financial risk whereas this cost became negligible in the other local optimum. Hence the question is again about what solution should be better to use. Another disadvantage of the stochastic approach is the time required to get the parameters of the exponential decay function for the probability of death. In principle, a high number of simulations should be used in the Monte Carlo procedure. The number of calculations could be reduced by reducing the number of direction-sectors but again a large number would produce more representative results. These results have been ratified with other examples in (Vázquez-Román et al., 2008). Solving the layout with the deterministic approach tends to produce more conservative layouts (Diaz-Ovalle et al., 2008). However, when the toxic material is too toxic this approach may produce layouts occupying a large area. This was the case for the example used in (Vázquez-Román et al., 2009). This approach has the advantage that no extra calculation is required to incorporate the wind effect since calm conditions and hence symmetric effect is assumed. Thus the deterministic approach tends to enforce prevention, mitigation and removal of hazards to reduce the required land. This is typically achieved by inserting devices so that the final layout becomes more expensive than the one produced with the stochastic approach. This approach is justified by the fact that several severe accidents have occurred when calm conditions prevailed.
Download or read book Manufacturing Plant Layout written by Edward John Phillips and published by . This book was released on 1997 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: A step-by-step guide to planning new factories and plant rearrangements, this book describes proven analytical methods for: Calculating space requirements, Activity-pair relationships, Materials handling analysis, Generating alternative layout. This proven strategy masterfully weaves together the very best elements of layout methods for manufacturing cells, JIT, demand-flow and constraint-based flow manufacturing philosophies, in addition to traditional job shop and assembly line operations. Learn how to methodically reduce or totally rid a design of profit eroders during the plan/design of a cost efficient manufacturing layout.
Download or read book Design of Simple and Robust Process Plants written by J. L. A. Koolen and published by John Wiley & Sons. This book was released on 2001-10-15 with total page 490 pages. Available in PDF, EPUB and Kindle. Book excerpt: The approaches to design process plants described in this book lead to process designs which require 30-40% less capital than usual. The book is unique since it is the first comprehensive work addressing both the total process design and operational approach. Technological developments during the last decade made the design of really competitive processes possible. Mechanical developments have resulted in reliable and robust equipment. Process developments have created opportunities to minimize the amount of equipment; furthermore, different logistic approaches, integration of process functionality and intensification of the unit operations are possible. Computer and control technology allows remote-control operation and first pass prime production. In this work design philosophies are discussed and their implementation is shown as a structured approach for planned and existing plants. Numerous examples are presented to illustrate what simple design can create. The work is intended for experienced engineers and managers involved in process design, control design and operation, but is also interesting for students. Project engineers and managers have to apply these new approaches to achieve competitive processes. "A process plant should meet the simplicity and robustness of a household refrigerator." This book has been written to allow to achieve this aim. "Chairman of the Judges Award" from IChemE 2003
Download or read book Plant Layout and Materials Handling written by James MacGregor Apple and published by . This book was released on 1977-05-15 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: This widely used text provides thorough coverage of modern layout and material handling principles and practices, stressing the important relationships of the management planning, product design, and process design functions with the problems of facilities design. Reflecting the author's wide experience in teaching and in industry, the book continues its highly effective step-by-step approach to developing and improving facility design. The extensively revised Third Edition devotes separate chapters to process design, use of quantitative techniques in analyzing material flow, computerized layout procedures, and facility location. Throughout, discussions are illustrated with forms and charts taken from successful practice, as well as many photographs, tables, and checklists. While the principal focus is the industrial plant, full recognition is given to the applicability of procedures and techniques to non-manufacturing establishments.
Download or read book Plant Layout and Design written by James Mendon Moore and published by . This book was released on 1962 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt: Textbook designed for undergraduate courses in industrial engineering and factory organization - covers location of industry, production planning, equipment, storage space, facilities for the provision of meals and health services, work study, etc., and includes ergonomics, operational research and mathematical programming. References, and selected bibliography at the end of each chapter.
Download or read book Introduction to Business written by Lawrence J. Gitman and published by . This book was released on 2018 with total page 732 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to Business covers the scope and sequence of most introductory business courses. The book provides detailed explanations in the context of core themes such as customer satisfaction, ethics, entrepreneurship, global business, and managing change. Introduction to Business includes hundreds of current business examples from a range of industries and geographic locations, which feature a variety of individuals. The outcome is a balanced approach to the theory and application of business concepts, with attention to the knowledge and skills necessary for student success in this course and beyond.
Download or read book Plant Layout written by Randolph W. Mallick and published by . This book was released on 2013-08 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Process Plant Layout written by Sean Moran and published by Butterworth-Heinemann. This book was released on 2016-11-16 with total page 758 pages. Available in PDF, EPUB and Kindle. Book excerpt: Process Plant Layout, Second Edition, explains the methodologies used by professional designers to layout process equipment and pipework, plots, plants, sites, and their corresponding environmental features in a safe, economical way. It is supported with tables of separation distances, rules of thumb, and codes of practice and standards. The book includes more than seventy-five case studies on what can go wrong when layout is not properly considered. Sean Moran has thoroughly rewritten and re-illustrated this book to reflect advances in technology and best practices, for example, changes in how designers balance layout density with cost, operability, and safety considerations. The content covers the ‘why’ underlying process design company guidelines, providing a firm foundation for career growth for process design engineers. It is ideal for process plant designers in contracting, consultancy, and for operating companies at all stages of their careers, and is also of importance for operations and maintenance staff involved with a new build, guiding them through plot plan reviews. Based on interviews with over 200 professional process plant designers Explains multiple plant layout methodologies used by professional process engineers, piping engineers, and process architects Includes advice on how to choose and use the latest CAD tools for plant layout Ensures that all methodologies integrate to comply with worldwide risk management legislation
Download or read book Facility Layout written by Miguel F. Anjos and published by Springer Nature. This book was released on 2021-04-24 with total page 121 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a structured approach to develop mathematical optimization formulations for several variants of facility layout. The range of layout problems covered includes row layouts, floor layouts, multi-floor layouts, and dynamic layouts. The optimization techniques used to formulate the problems are primarily mixed-integer linear programming, second-order conic programming, and semidefinite programming. The book also covers important practical considerations for solving the formulations. The breadth of approaches presented help the reader to learn how to formulate a variety of problems using mathematical optimization techniques. The book also illustrates the use of layout formulations in selected engineering applications, including manufacturing, building design, automotive, and hospital layout.
Download or read book Recent Trends in Product Design and Intelligent Manufacturing Systems written by B.B.V.L. Deepak and published by Springer Nature. This book was released on 2022-10-05 with total page 968 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents select proceedings of the 3rd Innovative Product Design and Intelligent Manufacturing System (IPDIMS 2020), held at National Institute of Technology (NIT) Rourkela, 30–31 December 2021. This volume covers the latest research topics in design and manufacturing fields of engineering. Some of the themes covered include Industry 4.0, smart manufacturing, advanced robotics and CAD/CAM/CIM. This book will be useful for students, researchers and professionals in the disciplines of mechatronics, mechanical, manufacturing, production and industrial engineering, especially those working on improvements in manufacturing technologies and development of resilient infrastructure in industry.
Download or read book Plant Layout and Facility Planning written by Jack Greene and published by CreateSpace. This book was released on 2013-09 with total page 210 pages. Available in PDF, EPUB and Kindle. Book excerpt: For the Kindle Store version, please refer to http: //www.amazon.com/Plant-Layout-Facility-Planning-ebook/dp/B00FAGME58/ref=sr_1_1?s=digital-text&ie=UTF8&qid=1379779924&sr=1-1&keywords=Plant+Layout+and+Facility+Planning Layout, or the physical organization of people, materials and machines within a workplace, is at the very heart of productivity. This book will enable the reader to create productive layouts quickly and smoothly. Plant layout and facility planning are closely associated in industrial and commercial enterprises, and affect operating efficiency and productivity now and in the future. Layout chapters include: Plant Layout, Facility Design, Floor Planning Layout benefits and concepts Layout and how it can enhance productivity Work flow and facility layout Sequence of actions The big picture for a layout Factors to consider in a layout and relocation Relocate for cost reasons Glossary of layout terms If you only read one layout chapter Step one, to create a layout What is the degree of difficulty? Block layout, and detailed layout What format, CAD or paper-dolls? Create layouts, explore options Relationships of layout components Ownership in a layout Tools to apply, for successful layouts Technology transfer, documentation The destination; prepare it Pack and move Master plan a facility Workplace layout Office move, a special case A jam-packed building and how to cope Relocation to an existing company facility Layout for the truly expert Layout during facility consolidation Chapters in the ection on Facility Relocation, Merger, and Consolidation include: Overview, a facility instead of or in addition to Time to expand Time to relocate Justification, both objective and subjective The marketplace which solicits business to locate in their areas Relocation incentives and taxes Just where, exactly Site search process Quality Of Life, and Culture Shock The need for confidentiality Red flags and warning signs Master Plan for a campus, of multiple facilities A "simple" move A "simple" expansion Create a facility from scratch Consolidation, merger, of equipment, facility or process Typical sequence of actions, for a facility project Chapters explain what and why, and list actions to create productive layouts quickly and smoothly within the physical constraints of the facility. They improve project management by highlighting which practices to utilize and which missteps to avoid, and extend the technical capabilities of your staff. This book will guide your organization through practical strategic and hands-on instruction, enable creation of new productive layouts quickly and smoothly within the physical constraints of the facility, as well as Consider and optimize factors which extend the layout's contribution now and through the years. Extend the technical capabilities of your staff . Improve project management by highlighting which practices to utilize and which missteps to avoid. A thoughtful layout can achieve many efficiencies in a new or existing facility. Facility layouts and floor plans tend to be replaced infrequently, because a revision can be expensive and cause disruption as it is installed. Better get it right.
Download or read book Plant Design Facility Layout Floor Planning written by Jack Greene and published by Createspace Independent Publishing Platform. This book was released on 2011-09-15 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book has been replaced by the author, who in September 2013 has published Plant Layout and Facility Planning Edition Two ISBN-13: 978-1491222393It is cheaper, and combines layout with facility planning since they are so closely related. Please look for it on Amazon.My book on all aspects of Industrial Engineering is also available now; Industrial Engineering: Theory, Practice & Application Business and Production Management, Productivity and Capacity ISBN-13: 978-1482301793. It includes all of the 2013 book concerning layout and facility planning.
Download or read book Optimal Plant Layout Design for Process focused Systems written by M. Khoshnevisan and published by Infinite Study. This book was released on with total page 13 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this paper we have proposed a semi-heuristic optimization algorithm for designing optimal plant layouts in process-focused manufacturing/service facilities. Our proposed algorithm marries the well-known CRAFT (Computerized Relative Allocation of Facilities Technique) with the Hungarian assignment algorithm.
Download or read book Process Plant Layout and Piping Design written by Ed Bausbacher and published by Prentice Hall. This book was released on 1993 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt: For mechanical and chemical engineers working for engineering construction as well as process manufacturing companies with responsibility for plant layout, piping, and construction; and for engineering students. Based on the authors' collective 65 years of experience in the engineering construction industry, this profusely illustrated, comprehensive guidebook presents tried-and-true workable methods and rules of thumb for plant layout and piping design for the process industries. Content is organized and presented for quick-reference on- the-job or for systematic study of specific topics. KEY TOPICS: Presents general concepts and principles of plant layout -- from basic terminology and input requirements to deliverables; deals with specific pieces of equipment and their most efficient layout in the overall plant design configuration; addresses the plant layout requirements for the most common process unit equipment; and considers the computerized tools that are now available to help plant layout and piping designers.
Download or read book Process Engineering and Plant Design written by Siddhartha Mukherjee and published by CRC Press. This book was released on 2021-12-28 with total page 507 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book provides the whole horizon of process engineering and plant design from concept phase through the execution to commissioning of the plant in the real practice. Providing a complete industrial perspective, the book: Covers the guidelines and standards followed in the industry and how engineering documents are generated using these standards Describes Hazardous Area Classification, Relief System Design, Revamp Engineering, Interaction with Other Disciplines, and Pre-commissioning and Commissioning Contains several illustrated practical examples, which clarify the fundamentals to a raw chemical engineer Includes description of a complete chemical project from concept to commissioning Treating the topic from the perspective of an industrial employee with extensive experience in process engineering and plant design, it aims to aid chemical and plant engineers to deal with decision making processes on strategic level, management tasks and leading functions beside the technical know-how.
Download or read book Process Equipment and Plant Design written by Subhabrata Ray and published by Elsevier. This book was released on 2020-05-29 with total page 884 pages. Available in PDF, EPUB and Kindle. Book excerpt: Process Equipment and Plant Design: Principles and Practices takes a holistic approach towards process design in the chemical engineering industry, dealing with the design of individual process equipment and its configuration as a complete functional system. Chapters cover typical heat and mass transfer systems and equipment included in a chemical engineering curriculum, such as heat exchangers, heat exchanger networks, evaporators, distillation, absorption, adsorption, reactors and more. The authors expand on additional topics such as industrial cooling systems, extraction, and topics on process utilities, piping and hydraulics, including instrumentation and safety basics that supplement the equipment design procedure and help to arrive at a complete plant design. The chapters are arranged in sections pertaining to heat and mass transfer processes, reacting systems, plant hydraulics and process vessels, plant auxiliaries, and engineered safety as well as a separate chapter showcasing examples of process design in complete plants. This comprehensive reference bridges the gap between industry and academia, while exploring best practices in design, including relevant theories in process design making this a valuable primer for fresh graduates and professionals working on design projects in the industry. Serves as a consolidated resource for process and plant design, including process utilities and engineered safety Bridges the gap between industry and academia by including practices in design and summarizing relevant theories Presents design solutions as a complete functional system and not merely the design of major equipment Provides design procedures as pseudo-code/flow-chart, along with practical considerations
Download or read book Design of Clothing Manufacturing Processes written by Jelka Geršak and published by Elsevier. This book was released on 2013-07-31 with total page 323 pages. Available in PDF, EPUB and Kindle. Book excerpt: The era of mass manufacturing of clothing and other textile products is coming to an end; what is emerging is a post-industrial production system that is able to achieve the goal of mass-customised, low volume production, where the conventional borders between product design, production and user are beginning to merge. To continue developing knowledge on how to design better products and services, we need to design better clothing manufacturing processes grounded in science, technology, and management to help the clothing industry to compete more effectively. Design of clothing manufacturing processes reviews key issues in the design of more rapid, integrated and flexible clothing manufacturing processes.The eight chapters of the book provide a detailed coverage of the design of clothing manufacturing processes using a systematic approach to planning, scheduling and control. The book starts with an overview of standardised clothing classification systems and terminologies for individual clothing types. Chapter 2 explores the development of standardised sizing systems. Chapter 3 reviews the key issues in the development of a garment collection. Chapters 4 to 7 discuss particular aspects of clothing production, ranging from planning and organization to monitoring and control. Finally, chapter 8 provides an overview of common quality requirements for clothing textile materials.Design of clothing manufacturing processes is intended for R&D managers, researchers, technologists and designers throughout the clothing industry, as well as academic researchers in the field of clothing design, engineering and other aspects of clothing production. Considers in detail the design of sizing and classification systems Discusses the planning required in all aspects of clothing production from design and pattern making to manufacture Overviews the management of clothing production and material quality requirements
