Download or read book A New Methodology for Yield Simulation of Integrated Circuits written by Carnegie-Mellon University. SRC-CMU Research Center for Computer-Aided Design and published by . This book was released on 1989 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Yield Simulation for Integrated Circuits written by D.M. Walker and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the summer of 1981 I was asked to consider the possibility of manufacturing a 600,000 transistor microprocessor in 1985. It was clear that the technology would only be capable of manufacturing 100,000-200,000 transistor chips with acceptable yields. The control store ROM occupied approximately half of the chip area, so I considered adding spare rows and columns to increase ROM yield. Laser-programmed polysilicon fuses would be used to switch between good and bad circuits. Since only half the chip area would have redundancy, I was concerned that the increase in yield would not outweigh the increased costs of testing and redundancy programming. The fabrication technology did not yet exist, so I was unable to experimentally verify the benefits of redundancy. When the technology did become available, it would be too late in the development schedule to spend time running test chips. The yield analysis had to be done analytically or by simulation. Analytic yield analysis techniques did not offer sufficient accuracy for dealing with complex structures. The simulation techniques then available were very labor-intensive and seemed more suitable for redundant memories and other very regular structures [Stapper 80J. I wanted a simulator that would allow me to evaluate the yield of arbitrary redundant layouts, hence I termed such a simulator a layout or yield simulator. Since I was unable to convince anyone to build such a simulator for me, I embarked on the research myself.
Download or read book Yield Aware Analog IC Design and Optimization in Nanometer scale Technologies written by António Manuel Lourenço Canelas and published by Springer Nature. This book was released on 2020-03-20 with total page 254 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a new methodology with reduced time impact to address the problem of analog integrated circuit (IC) yield estimation by means of Monte Carlo (MC) analysis, inside an optimization loop of a population-based algorithm. The low time impact on the overall optimization processes enables IC designers to perform yield optimization with the most accurate yield estimation method, MC simulations using foundry statistical device models considering local and global variations. The methodology described by the authors delivers on average a reduction of 89% in the total number of MC simulations, when compared to the exhaustive MC analysis over the full population. In addition to describing a newly developed yield estimation technique, the authors also provide detailed background on automatic analog IC sizing and optimization.
Download or read book Yield and Variability Optimization of Integrated Circuits written by Jian Cheng Zhang and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: Traditionally, Computer Aided Design (CAD) tools have been used to create the nominal design of an integrated circuit (IC), such that the circuit nominal response meets the desired performance specifications. In reality, however, due to the disturbances ofthe IC manufacturing process, the actual performancesof the mass produced chips are different than those for the nominal design. Even if the manufacturing process were tightly controlled, so that there were little variations across the chips manufactured, the environmentalchanges (e. g. those oftemperature, supply voltages, etc. ) would alsomakethe circuit performances vary during the circuit life span. Process-related performance variations may lead to low manufacturing yield, and unacceptable product quality. For these reasons, statistical circuit design techniques are required to design the circuit parameters, taking the statistical process variations into account. This book deals with some theoretical and practical aspects of IC statistical design, and emphasizes how they differ from those for discrete circuits. It de scribes a spectrum of different statistical design problems, such as parametric yield optimization, generalized on-target design, variability minimization, per formance tunning, and worst-case design. The main emphasis of the presen tation is placed on the principles and practical solutions for performance vari ability minimization. It is hoped that the book may serve as an introductory reference material for various groups of IC designers, and the methodologies described will help them enhance the circuit quality and manufacturability. The book containsseven chapters.
Download or read book The Application of Yield Surface Modeling Methodology to Digital CMOS Integrated Circuits written by David William Feldbaumer and published by . This book was released on 1990 with total page 572 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book VLSI Design for Manufacturing Yield Enhancement written by Stephen W. Director and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 299 pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the keys to success in the IC industry is getting a new product to market in a timely fashion and being able to produce that product with sufficient yield to be profitable. There are two ways to increase yield: by improving the control of the manufacturing process and by designing the process and the circuits in such a way as to minimize the effect of the inherent variations of the process on performance. The latter is typically referred to as "design for manufacture" or "statistical design". As device sizes continue to shrink, the effects of the inherent fluctuations in the IC fabrication process will have an even more obvious effect on circuit performance. And design for manufacture will increase in importance. We have been working in the area of statistically based computer aided design for more than 13 years. During the last decade we have been working with each other, and individually with our students, to develop methods and CAD tools that can be used to improve yield during the design and manufacturing phases of IC realization. This effort has resulted in a large number of publications that have appeared in a variety of journals and conference proceedings. Thus our motivation in writing this book is to put, in one place, a description of our approach to IC yield enhancement. While the work that is contained in this book has appeared in the open literature, we have attempted to use a consistent notation throughout this book.
Download or read book Masters Theses in the Pure and Applied Sciences written by Wade H. Shafer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 421 pages. Available in PDF, EPUB and Kindle. Book excerpt: Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS) * at Purdue University in 1957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all con cerned if the printing and distribution of the volumes were handled by an interna tional publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Cor poration of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 34 (thesis year 1989) a total of 13,377 theses titles from 26 Canadian and 184 United States universities. We are sure that this broader base for these titles reported will greatly enhance the value of this important annual reference work. While Volume 34 reports theses submitted in 1989, on occasion, certain univer sities do report theses submitted in previous years but not reported at the time.
Download or read book Integrated Circuit Manufacturability written by José Pineda de Gyvez and published by John Wiley & Sons. This book was released on 1998-10-30 with total page 338 pages. Available in PDF, EPUB and Kindle. Book excerpt: "INTEGRATED CIRCUIT MANUFACTURABILITY provides comprehensive coverage of the process and design variables that determine the ease and feasibility of fabrication (or manufacturability) of contemporary VLSI systems and circuits. This book progresses from semiconductor processing to electrical design to system architecture. The material provides a theoretical background as well as case studies, examining the entire design for the manufacturing path from circuit to silicon. Each chapter includes tutorial and practical applications coverage. INTEGRATED CIRCUIT MANUFACTURABILITY illustrates the implications of manufacturability at every level of abstraction, including the effects of defects on the layout, their mapping to electrical faults, and the corresponding approaches to detect such faults. The reader will be introduced to key practical issues normally applied in industry and usually required by quality, product, and design engineering departments in today's design practices: * Yield management strategies * Effects of spot defects * Inductive fault analysis and testing * Fault-tolerant architectures and MCM testing strategies. This book will serve design and product engineers both from academia and industry. It can also be used as a reference or textbook for introductory graduate-level courses on manufacturing."
Download or read book Selected Papers on Statistical Design of Integrated Circuits written by Andrzej J. Strojwas and published by . This book was released on 1987 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Defect and Fault Tolerance in VLSI Systems written by C.H. Stapper and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Higher circuit densities, increasingly more complex application ohjectives, and advanced packaging technologies have suhstantially increased the need to incorporate defect-tolerance and fault-tolerance in the design of VLSI and WSI systems. The goals of defect-tolerance and fault-tolerance are yield enhancement and improved reliahility. The emphasis on this area has resulted in a new field of interdisciplinary scientific research. I n fact, advanced methods of defect/fault control and tolerance are resulting in enhanced manufacturahility and productivity of integrated circuit chips, VI.SI systems, and wafer scale integrated circuits. In 1987, Dr. W. Moore organized an "International Workshop on Designing for Yield" at Oxford University. Edited papers of that workshop were published in reference [II. The participants in that workshop agreed that meetings of this type should he con tinued. preferahly on a yearly hasis. It was Dr. I. Koren who organized the "IEEE Inter national Workshop on Defect and Fault Tolerance in VLSI Systems" in Springfield Massachusetts the next year. Selected papers from that workshop were puhlished as the first volume of this series [21.
Download or read book Analog Integrated Circuit Design by Simulation Techniques Tools and Methods written by Ugur Cilingiroglu and published by McGraw Hill Professional. This book was released on 2019-03-29 with total page 577 pages. Available in PDF, EPUB and Kindle. Book excerpt: Learn the principles and practices of simulation-based analog IC design This comprehensive textbook and on-the-job reference offers clear instruction on analog integrated circuit design using the latest simulation techniques. Ideal for graduate students and professionals alike, the book shows, step by step, how to develop and deploy integrated circuits for cutting-edge Internet of Things (IoT) and other applications. Analog Integrated Circuit Design by Simulation: Techniques, Tools, and Methods lays out practical, ready-to-apply engineering strategies. Application layer, device layer, and circuit layer IC design are covered in complete detail. You will learn how to tackle real-world design problems and avoid long cycles of trial and error. Coverage includes: First-order DC response Unified closed-loop model Accurate modeling of DC response Frequency and step response Multi-pole dynamic response and stability Effect of external network on differential gain Continuous-time and discrete-time amplifiers MOSFET, NMOS, and PMOS characteristics Small-signal modeling and circuit analysis Resistor and capacitor design Current sources, sinks, and mirrors Basic, symmetrical, folded-cascode, and Miller OTAs Opamps with source-follower and common-source output stages Fully differential OTAs and opamps
Download or read book Wafer Scale Integration written by Earl E. Swartzlander Jr. and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 515 pages. Available in PDF, EPUB and Kindle. Book excerpt: Wafer Scale Integration (WSI) is the culmination of the quest for larger integrated circuits. In VLSI chips are developed by fabricating a wafer with hundreds of identical circuits, testing the circuits, dicing the wafer, and packaging the good dice. In contrast in WSI, a wafer is fabricated with several types of circuits (generally referred to as cells), with multiple instances of each cell type, the cells are tested, and good cells are interconnected to realize a system on the wafer. Since most signal lines stay on the wafer, stray capacitance is low, so that high speeds are achieved with low power consumption. For the same technology a WSI implementation may be a factor of five faster, dissipate a factor of ten less power, and require one hundredth to one thousandth the volume. Successful development of WSI involves many overlapping disciplines, ranging from architecture to test design to fabrication (including laser linking and cutting, multiple levels of interconnection, and packaging). This book concentrates on the areas that are unique to WSI and that are as a result not well covered by any of the many books on VLSI design. A unique aspect of WSI is that the finished circuits are so large that there will be defects in some portions of the circuit. Accordingly much attention must be devoted to designing architectures that facilitate fault detection and reconfiguration to of WSI include fabrication circumvent the faults. Other unique aspects technology and packaging.
Download or read book Process Variations and Probabilistic Integrated Circuit Design written by Manfred Dietrich and published by Springer Science & Business Media. This book was released on 2011-11-20 with total page 261 pages. Available in PDF, EPUB and Kindle. Book excerpt: Uncertainty in key parameters within a chip and between different chips in the deep sub micron area plays a more and more important role. As a result, manufacturing process spreads need to be considered during the design process. Quantitative methodology is needed to ensure faultless functionality, despite existing process variations within given bounds, during product development. This book presents the technological, physical, and mathematical fundamentals for a design paradigm shift, from a deterministic process to a probability-orientated design process for microelectronic circuits. Readers will learn to evaluate the different sources of variations in the design flow in order to establish different design variants, while applying appropriate methods and tools to evaluate and optimize their design.
Download or read book Architecture Design and Validation Methods written by Egon Börger and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 363 pages. Available in PDF, EPUB and Kindle. Book excerpt: This state-of-the-art survey gives a systematic presentation of recent advances in the design and validation of computer architectures. The book covers a comprehensive range of architecture design and validation methods, from computer aided high-level design of VLSI circuits and systems to layout and testable design, including the modeling and synthesis of behavior and dataflow, cell-based logic optimization, machine assisted verification, and virtual machine design.
Download or read book Computer Aided Design of Analog Integrated Circuits and Systems written by Rob A. Rutenbar and published by John Wiley & Sons. This book was released on 2002-05-06 with total page 773 pages. Available in PDF, EPUB and Kindle. Book excerpt: The tools and techniques you need to break the analog design bottleneck! Ten years ago, analog seemed to be a dead-end technology. Today, System-on-Chip (SoC) designs are increasingly mixed-signal designs. With the advent of application-specific integrated circuits (ASIC) technologies that can integrate both analog and digital functions on a single chip, analog has become more crucial than ever to the design process. Today, designers are moving beyond hand-crafted, one-transistor-at-a-time methods. They are using new circuit and physical synthesis tools to design practical analog circuits; new modeling and analysis tools to allow rapid exploration of system level alternatives; and new simulation tools to provide accurate answers for analog circuit behaviors and interactions that were considered impossible to handle only a few years ago. To give circuit designers and CAD professionals a better understanding of the history and the current state of the art in the field, this volume collects in one place the essential set of analog CAD papers that form the foundation of today's new analog design automation tools. Areas covered are: * Analog synthesis * Symbolic analysis * Analog layout * Analog modeling and analysis * Specialized analog simulation * Circuit centering and yield optimization * Circuit testing Computer-Aided Design of Analog Integrated Circuits and Systems is the cutting-edge reference that will be an invaluable resource for every semiconductor circuit designer and CAD professional who hopes to break the analog design bottleneck.
Download or read book Variation Aware Design of Custom Integrated Circuits A Hands on Field Guide written by Trent McConaghy and published by Springer Science & Business Media. This book was released on 2012-10-02 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book targets custom IC designers who are encountering variation issues in their designs, especially for modern process nodes at 45nm and below, such as statistical process variations, environmental variations, and layout effects. It teaches them the state-of-the-art in Variation-Aware Design tools, which help the designer to analyze quickly the variation effects, identify the problems, and fix the problems. Furthermore, this book describes the algorithms and algorithm behavior/performance/limitations, which is of use to designers considering these tools, designers using these tools, CAD researchers, and CAD managers.
Download or read book A Top Down Constraint Driven Design Methodology for Analog Integrated Circuits written by Henry Chang and published by Springer Science & Business Media. This book was released on 1997 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analog circuit design is often the bottleneck when designing mixed analog-digital systems. A Top-Down, Constraint-Driven Design Methodology for Analog Integrated Circuits presents a new methodology based on a top-down, constraint-driven design paradigm that provides a solution to this problem. This methodology has two principal advantages: (1) it provides a high probability for the first silicon which meets all specifications, and (2) it shortens the design cycle. A Top-Down, Constraint-Driven Design Methodology for Analog Integrated Circuits is part of an ongoing research effort at the University of California at Berkeley in the Electrical Engineering and Computer Sciences Department. Many faculty and students, past and present, are working on this design methodology and its supporting tools. The principal goals are: (1) developing the design methodology, (2) developing and applying new tools, and (3) `proving' the methodology by undertaking `industrial strength' design examples. The work presented here is neither a beginning nor an end in the development of a complete top-down, constraint-driven design methodology, but rather a step in its development. This work is divided into three parts. Chapter 2 presents the design methodology along with foundation material. Chapters 3-8 describe supporting concepts for the methodology, from behavioral simulation and modeling to circuit module generators. Finally, Chapters 9-11 illustrate the methodology in detail by presenting the entire design cycle through three large-scale examples. These include the design of a current source D/A converter, a Sigma-Delta A/D converter, and a video driver system. Chapter 12 presents conclusions and current research topics. A Top-Down, Constraint-Driven Design Methodology for Analog Integrated Circuits will be of interest to analog and mixed-signal designers as well as CAD tool developers.
