Download or read book A Method for Accounting for Pile Setup and Relaxation in Pile Design and Quality Assurance written by Prasenjit Basu and published by Purdue University Press. This book was released on 2009-08-01 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: When piles are installed by jacking or driving, they cause substantial changes in the state of soil located near the pile. These changes result from the complex loading imposed on the soil by expansion of a cylindrical cavity to make room for the pile, by multiple cycles of shearing in the vertical direction as the pile gradually moves down into the ground, and by the slow drainage associated with clayey soils. If a pile is load-tested a short time after installation, it will develop an axial resistance that reflects the existence in the soil of the excess pore pressures caused by the installation process. After the excess pore pressures dissipate, the axial pile resistance will be different from that measured in the short term. This difference is referred to as pile setup (if the resistance increases) or relaxation (if the resistance drops). This report focuses on the pile setup observed in clayey soils, in which it can be quite significant. Pile setup in clays result primarily from shaft resistance gains with time after installation because the base resistance contributes proportionally much less in soft to medium stiff clays, which are the focus of the research. Accordingly, our focus has been on analyzing setup in shaft resistance, validating the equations resulting from these analyses and then proposing design and quality assurance procedures based on the results of the analyses.
Download or read book Basics of Foundation Design written by Bengt Fellenius and published by Lulu.com. This book was released on 2017-03-17 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt: The "Red Book" presents a background to conventional foundation analysis and design. The text is not intended to replace the much more comprehensive 'standard' textbooks, but rather to support and augment these in a few important areas, supplying methods applicable to practical cases handled daily by practising engineers and providing the basic soil mechanics background to those methods. It concentrates on the static design for stationary foundation conditions. Although the topic is far from exhaustively treated, it does intend to present most of the basic material needed for a practising engineer involved in routine geotechnical design, as well as provide the tools for an engineering student to approach and solve common geotechnical design problems.
Download or read book Canadian Foundation Engineering Manual written by Canadian Geotechnical Society and published by Richmond, B.C. : Canadian Geotechnical Society. This book was released on 1992 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Geotechnical Investigation and Design Tables written by Burt G. Look and published by CRC Press. This book was released on 2007-04-26 with total page 356 pages. Available in PDF, EPUB and Kindle. Book excerpt: This practical handbook of properties for soils and rock contains, in a concise tabular format, the key issues relevant to geotechnical investigations, assessments and designs in common practice. In addition, there are brief notes on the application of the tables. These data tables are compiled for experienced geotechnical professionals who require a reference document to access key information. There is an extensive database of correlations for different applications. The book should provide a useful bridge between soil and rock mechanics theory and its application to practical engineering solutions. The initial chapters deal with the planning of the geotechnical investigation, the classification of the soil and rock properties and some of the more used testing is then covered. Later chapters show the reliability and correlations that are used to convert that data in the interpretative and assessment phase of the project. The final chapters apply some of these concepts to geotechnical design. This book is intended primarily for practicing geotechnical engineers working in investigation, assessment and design, but should provide a useful supplement for postgraduate courses.
Download or read book Theory and Practice of Pile Foundations written by Wei Dong Guo and published by CRC Press. This book was released on 2012-11-14 with total page 579 pages. Available in PDF, EPUB and Kindle. Book excerpt: Pile Foundations are an essential basis for many structures. It is vital that they be designed with the utmost reliability, because the cost of failure is potentially huge. Covering a whole range of design issues relating to pile design, this book presents economical and efficient design solutions and demonstrates them using real world examples. Coverage includes nonlinear response of single piles to vertical or torsional loading and to cyclic lateral loading, as well as prediction of nonlinear response of lateral pile groups, vertically loaded pile groups and the design of slope stabilising piles. Most solutions are provided as closed-form expressions. Theory and Practice of Pile Foundations is: illustrated with case studies accompanied by practical applications in Excel and MathCad the first book to incorporate nonlinear interaction into pile design. A valuable resource for students of geotechnical engineering taking courses in foundations and a vital tool for engineers designing pile foundations.
Download or read book Pile Design and Construction Practice Fifth Edition written by Michael Tomlinson and published by CRC Press. This book was released on 2007-12-06 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: This international handbook is essential for geotechnical engineers and engineering geologists responsible for designing and constructing piled foundations. It explains general principles and practice and details current types of pile, piling equipment and methods. It includes calculations of the resistance of piles to compressive loads, pile groups under compressive loading, piled foundations for resisting uplift and lateral loading and the structural design of piles and pile groups. Marine structures, miscellaneous problems (including machinery foundations, underpinning, mining subsidence areas, contracts and frozen ground), durability of piled foundations, ground investigations, and pile testing are also covered. It introduces the 2005 version of Eurocode7, BS 8004 and other codes, and refers to BS 6349 on maritime structures, and new forms of civil engineering contracts suitable for piling projects. It includes numerous worked examples to the codes, many based on actual problems. It also gives very comprehensive information for students.
Download or read book Foundation Design Principles and Practices written by Donald P. Coduto and published by Pearson Higher Ed. This book was released on 2013-10-03 with total page 889 pages. Available in PDF, EPUB and Kindle. Book excerpt: For undergraduate/graduate-level foundation engineering courses. Covers the subject matter thoroughly and systematically, while being easy to read. Emphasizes a thorough understanding of concepts and terms before proceeding with analysis and design, and carefully integrates the principles of foundation engineering with their application to practical design problems.
Download or read book Design of Pile Foundations written by US Army Corps of Engineers and published by . This book was released on 2005-01-01 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual provides information, foundation exploration and testing procedures, load test methods, analysis techniques, allowable criteria, design procedures, and construction consideration for the selection, design, and installation of pile foundations. The guidance is based on the present state of the technology for pile-soil-structure-foundation interaction behavior. This manual provides design guidance intended specifically for the geotechnical and structural engineer but also provides essential information for others interested in pile foundations such as the construction engineer in understanding construction techniques related to pile behavior during installation. Since the understanding of the physical causes of pile foundation behavior is actively expanding by better definition through ongoing research, prototype, model pile, and pile group testing and development of more refined analytical models, this manual is intended to provide examples and procedures of what has been proven successful. This is not the last nor final word on the state of the art for this technology. We expect, as further practical design and installation procedures are developed from the expansion of this technology, that these updates will be issued as changes to this manual.
Download or read book Tall Building Foundation Design written by Harry G. Poulos and published by CRC Press. This book was released on 2017-07-20 with total page 761 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive guide to the design of foundations for tall buildings. After a general review of the characteristics of tall buildings, various foundation options are discussed followed by the general principles of foundation design as applied to tall buildings. Considerable attention is paid to the methods of assessment of the geotechnical design parameters, as this is a critical component of the design process. A detailed treatment is then given to foundation design for various conditions, including ultimate stability, serviceability, ground movements, dynamic loadings and seismic loadings. Basement wall design is also addressed. The last part of the book deals with pile load testing and foundation performance measurement, and finally, the description of a number of case histories. A feature of the book is the emphasis it places on the various stages of foundation design: preliminary, detailed and final, and the presentation of a number of relevant methods of design associated with each stage.
Download or read book Load and Resistance Factor Design LRFD for Deep Foundations written by Samuel G. Paikowsky and published by Transportation Research Board. This book was released on 2004 with total page 87 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction and research approach -- Findings -- Interpretation, appraisal, and applications -- Conclusions and suggested research -- Bibliography -- Appendixes.
Download or read book Biochar for Environmental Management written by Dr. Johannes Lehmann and published by Earthscan. This book was released on 2009 with total page 449 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Biochar is the carbon-rich product when biomass (such as wood, manure, or crop residues) is heated in a closed container with little or no available air. It can be used to improve agriculture and the environment in several ways, and its stability in soil and superior nutrient-retention properties make it an ideal soil amendment to increase crop yields. In addition to this, biochar sequestration, in combination with sustainable biomass production, can be carbon-negative and therefore used to actively remove carbon dioxide from the atmosphere, with major implications for mitigation of climate change. Biochar production can also be combined with bioenergy production through the use of the gases that are given off in the pyrolysis process.This book is the first to synthesize the expanding research literature on this topic. The book's interdisciplinary approach, which covers engineering, environmental sciences, agricultural sciences, economics and policy, is a vital tool at this stage of biochar technology development. This comprehensive overview of current knowledge will be of interest to advanced students, researchers and professionals in a wide range of disciplines"--Provided by publisher.
Download or read book Foundation Design written by N. S. V. Kamesware Rao and published by John Wiley & Sons. This book was released on 2010-12-30 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: In Foundation Design: Theory and Practice, Professor N. S. V. Kameswara Rao covers the key aspects of the subject, including principles of testing, interpretation, analysis, soil-structure interaction modeling, construction guidelines, and applications to rational design. Rao presents a wide array of numerical methods used in analyses so that readers can employ and adapt them on their own. Throughout the book the emphasis is on practical application, training readers in actual design procedures using the latest codes and standards in use throughout the world. Presents updated design procedures in light of revised codes and standards, covering: American Concrete Institute (ACI) codes Eurocode 7 Other British Standard-based codes including Indian codes Provides background materials for easy understanding of the topics, such as: Code provisions for reinforced concrete Pile design and construction Machine foundations and construction practices Tests for obtaining the design parameters Features subjects not covered in other foundation design texts: Soil-structure interaction approaches using analytical, numerical, and finite element methods Analysis and design of circular and annular foundations Analysis and design of piles and groups subjected to general loads and movements Contains worked out examples to illustrate the analysis and design Provides several problems for practice at the end of each chapter Lecture materials for instructors available on the book's companion website Foundation Design is designed for graduate students in civil engineering and geotechnical engineering. The book is also ideal for advanced undergraduate students, contractors, builders, developers, heavy machine manufacturers, and power plant engineers. Students in mechanical engineering will find the chapter on machine foundations helpful for structural engineering applications. Companion website for instructor resources: www.wiley.com/go/rao
Download or read book Crystal Plasticity Finite Element Methods written by Franz Roters and published by John Wiley & Sons. This book was released on 2011-08-04 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by the leading experts in computational materials science, this handy reference concisely reviews the most important aspects of plasticity modeling: constitutive laws, phase transformations, texture methods, continuum approaches and damage mechanisms. As a result, it provides the knowledge needed to avoid failures in critical systems udner mechanical load. With its various application examples to micro- and macrostructure mechanics, this is an invaluable resource for mechanical engineers as well as for researchers wanting to improve on this method and extend its outreach.
Download or read book IFCEE 2015 written by Magued Iskander and published by . This book was released on 2015 with total page 2845 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design of Axially Loaded Piles European Practice written by F. De Cock and published by CRC Press. This book was released on 2020-12-18 with total page 528 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is unique on the subject because it is not so much a collection of individual work, but basically comprising national reports from most European countries on the present-day design methods, as prescribed in more or less strict national codes or recommendations and so daily used in practice by consulting engineers and contractors. As far as already implemented, the application of these methods within the framework of Eurocode 7 is described as well. In order to improve the understanding of the design methods, the national papers also consider aspects such as the local piling practice, limitations of the design methods, some practical examples and particular national experiences. The proceedings also include the contributions of two invited speakers as well as those of the three session discussion leaders, focusing on some particular aspects with regards to pile design. The book is of particular interest for those who are involved with pile design in practice, consulting engineers, piling contractors, control organisms as well as those dealing with geotechnical normalisation and research work.
Download or read book New York Magazine written by and published by . This book was released on 1979-02-12 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt: New York magazine was born in 1968 after a run as an insert of the New York Herald Tribune and quickly made a place for itself as the trusted resource for readers across the country. With award-winning writing and photography covering everything from politics and food to theater and fashion, the magazine's consistent mission has been to reflect back to its audience the energy and excitement of the city itself, while celebrating New York as both a place and an idea.
Download or read book Bulletin of the Atomic Scientists written by and published by . This book was released on 1953-05 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Bulletin of the Atomic Scientists is the premier public resource on scientific and technological developments that impact global security. Founded by Manhattan Project Scientists, the Bulletin's iconic "Doomsday Clock" stimulates solutions for a safer world.
