Download or read book A Mathematical Model of Thermal Oil Recovery in a Forward In situ Combustion Process written by Noaman El-Khatib and published by . This book was released on 1973 with total page 456 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Numerical Modeling of Thermal Recovery Processes written by Mohamed Yousef Soliman and published by . This book was released on 1979 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Efficient Simulation of Thermal Enhanced Oil Recovery Processes written by Zhouyuan Zhu and published by Stanford University. This book was released on 2011 with total page 237 pages. Available in PDF, EPUB and Kindle. Book excerpt: Simulating thermal processes is usually computationally expensive because of the complexity of the problem and strong nonlinearities encountered. In this work, we explore novel and efficient simulation techniques to solve thermal enhanced oil recovery problems. We focus on two major topics: the extension of streamline simulation for thermal enhanced oil recovery and the efficient simulation of chemical reaction kinetics as applied to the in-situ combustion process. For thermal streamline simulation, we first study the extension to hot water flood processes, in which we have temperature induced viscosity changes and thermal volume changes. We first compute the pressure field on an Eulerian grid. We then solve for the advective parts of the mass balance and energy equations along the individual streamlines, accounting for the compressibility effects. At the end of each global time step, we account for the nonadvective terms on the Eulerian grid along with gravity using operator splitting. We test our streamline simulator and compare the results with a commercial thermal simulator. Sensitivity studies for compressibility, gravity and thermal conduction effects are presented. We further extended our thermal streamline simulation to steam flooding. Steam flooding exhibits large volume changes and compressibility associated with the phase behavior of steam, strong gravity segregation and override, and highly coupled energy and mass transport. To overcome these challenges we implement a novel pressure update along the streamlines, a Glowinski scheme operator splitting and a preliminary streamline/finite volume hybrid approach. We tested our streamline simulator on a series of test cases. We compared our thermal streamline results with those computed by a commercial thermal simulator for both accuracy and efficiency. For the cases investigated, we are able to retain solution accuracy, while reducing computational cost and gaining connectivity information from the streamlines. These aspects are useful for reservoir engineering purposes. In traditional thermal reactive reservoir simulation, mass and energy balance equations are solved numerically on discretized reservoir grid blocks. The reaction terms are calculated through Arrhenius kinetics using cell-averaged properties, such as averaged temperature and reactant concentrations. For the in-situ combustion process, the chemical reaction front is physically very narrow, typically a few inches thick. To capture accurately this front, centimeter-sized grids are required that are orders of magnitude smaller than the affordable grid block sizes for full field reservoir models. To solve this grid size effect problem, we propose a new method based on a non-Arrhenius reaction upscaling approach. We do not resolve the combustion front on the grid, but instead use a subgrid-scale model that captures the overall effects of the combustion reactions on flow and transport, i.e. the amount of heat released, the amount of oil burned and the reaction products generated. The subgrid-scale model is calibrated using fine-scale highly accurate numerical simulation and laboratory experiments. This approach significantly improves the computational speed of in-situ combustion simulation as compared to traditional methods. We propose the detailed procedures to implement this methodology in a field-scale simulator. Test cases illustrate the solution consistency when scaling up the grid sizes in multidimensional heterogeneous problems. The methodology is also applicable to other subsurface reactive flow modeling problems with fast chemical reactions and sharp fronts. Displacement front stability is a major concern in the design of all the enhanced oil recovery processes. Historically, premature combustion front break through has been an issue for field operations of in-situ combustion. In this work, we perform detailed analysis based on both analytical methods and numerical simulation. We identify the different flow regimes and several driving fronts in a typical 1D ISC process. For the ISC process in a conventional mobile heavy oil reservoir, we identify the most critical front as the front of steam plateau driving the cold oil bank. We discuss the five main contributors for this front stability/instability: viscous force, condensation, heat conduction, coke plugging and gravity. Detailed numerical tests are performed to test and rank the relative importance of all these different effects.
Download or read book Thermal Methods of Oil R written by Burger J. and published by Editions OPHRYS. This book was released on 1985 with total page 456 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Efficient Simulation of Thermal Enhanced Oil Recovery Processes written by Zhouyuan Zhu and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Simulating thermal processes is usually computationally expensive because of the complexity of the problem and strong nonlinearities encountered. In this work, we explore novel and efficient simulation techniques to solve thermal enhanced oil recovery problems. We focus on two major topics: the extension of streamline simulation for thermal enhanced oil recovery and the efficient simulation of chemical reaction kinetics as applied to the in-situ combustion process. For thermal streamline simulation, we first study the extension to hot water flood processes, in which we have temperature induced viscosity changes and thermal volume changes. We first compute the pressure field on an Eulerian grid. We then solve for the advective parts of the mass balance and energy equations along the individual streamlines, accounting for the compressibility effects. At the end of each global time step, we account for the nonadvective terms on the Eulerian grid along with gravity using operator splitting. We test our streamline simulator and compare the results with a commercial thermal simulator. Sensitivity studies for compressibility, gravity and thermal conduction effects are presented. We further extended our thermal streamline simulation to steam flooding. Steam flooding exhibits large volume changes and compressibility associated with the phase behavior of steam, strong gravity segregation and override, and highly coupled energy and mass transport. To overcome these challenges we implement a novel pressure update along the streamlines, a Glowinski scheme operator splitting and a preliminary streamline/finite volume hybrid approach. We tested our streamline simulator on a series of test cases. We compared our thermal streamline results with those computed by a commercial thermal simulator for both accuracy and efficiency. For the cases investigated, we are able to retain solution accuracy, while reducing computational cost and gaining connectivity information from the streamlines. These aspects are useful for reservoir engineering purposes. In traditional thermal reactive reservoir simulation, mass and energy balance equations are solved numerically on discretized reservoir grid blocks. The reaction terms are calculated through Arrhenius kinetics using cell-averaged properties, such as averaged temperature and reactant concentrations. For the in-situ combustion process, the chemical reaction front is physically very narrow, typically a few inches thick. To capture accurately this front, centimeter-sized grids are required that are orders of magnitude smaller than the affordable grid block sizes for full field reservoir models. To solve this grid size effect problem, we propose a new method based on a non-Arrhenius reaction upscaling approach. We do not resolve the combustion front on the grid, but instead use a subgrid-scale model that captures the overall effects of the combustion reactions on flow and transport, i.e. the amount of heat released, the amount of oil burned and the reaction products generated. The subgrid-scale model is calibrated using fine-scale highly accurate numerical simulation and laboratory experiments. This approach significantly improves the computational speed of in-situ combustion simulation as compared to traditional methods. We propose the detailed procedures to implement this methodology in a field-scale simulator. Test cases illustrate the solution consistency when scaling up the grid sizes in multidimensional heterogeneous problems. The methodology is also applicable to other subsurface reactive flow modeling problems with fast chemical reactions and sharp fronts. Displacement front stability is a major concern in the design of all the enhanced oil recovery processes. Historically, premature combustion front break through has been an issue for field operations of in-situ combustion. In this work, we perform detailed analysis based on both analytical methods and numerical simulation. We identify the different flow regimes and several driving fronts in a typical 1D ISC process. For the ISC process in a conventional mobile heavy oil reservoir, we identify the most critical front as the front of steam plateau driving the cold oil bank. We discuss the five main contributors for this front stability/instability: viscous force, condensation, heat conduction, coke plugging and gravity. Detailed numerical tests are performed to test and rank the relative importance of all these different effects.
Download or read book Interpretation of In situ Combustion Thermal Oil Recovery Falloff Tests written by Michael Obi Onyekonwu and published by . This book was released on 1985 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Heavy Crude Oil Recovery written by E. Okandan and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 431 pages. Available in PDF, EPUB and Kindle. Book excerpt: Within the last 10 years the world has come to a point where the easily explorable oil deposits have now been found, and it is anticipated that such deposits will be depleted by the beginning of the Twenty-first Century. However, the increasing demand of man kind for energy has caused technologists to look into ways of find ing new sources or to reevaluat:e unconventional sources which, in the past, have not been economical. In this respect, heavy crude and tar sand oils are becoming important in fulfilling the world's energy requirements. What are heavy crude and tar sand oils? There is still some confusion as to their definitions, inasmuch as they vary among organizations and countries. In an effort to set agreed meanings, UNITAR, in a meeting in February 1982 in Venezuela, proposed the following definitions (see also Table 1): 1. Heavy crude oil and tar sand oil are petroleum or petroleum like liquids or semi-solids naturally occurring in porous media. The porous media are sands, sandstone, and carbonate rocks. 2. These oils will be characterized by viscosity and density. Viscosity will be used to define heavy crude oil and tar sand oil, and density (oAPI) will be used when viscosity measurements are not available. 3. Heavy crude oil has a gas-free viscosity of 100-10000 mPa.s (cp) 3 o at reservoir temperatures, or a density of 943 kg/m (20 API) 3 o o to 1000 kg/m (10 API) at 15.6 C and at atmospheric oressure.
Download or read book Computer Simulation of the Forward In Situ Combustion Oil Recovery Process Using a Stream Channel Model written by Abdul-Fadi Z. Jarjur and published by . This book was released on 1977 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Recovery written by Michael Prats and published by . This book was released on 1982 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Petroleum Abstracts written by and published by . This book was released on 1993 with total page 1752 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mathematical and Numerical Modeling in Porous Media written by Martin A. Diaz Viera and published by CRC Press. This book was released on 2012-07-24 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Porous media are broadly found in nature and their study is of high relevance in our present lives. In geosciences porous media research is fundamental in applications to aquifers, mineral mines, contaminant transport, soil remediation, waste storage, oil recovery and geothermal energy deposits. Despite their importance, there is as yet no complete understanding of the physical processes involved in fluid flow and transport. This fact can be attributed to the complexity of the phenomena which include multicomponent fluids, multiphasic flow and rock-fluid interactions. Since its formulation in 1856, Darcy’s law has been generalized to describe multi-phase compressible fluid flow through anisotropic and heterogeneous porous and fractured rocks. Due to the scarcity of information, a high degree of uncertainty on the porous medium properties is commonly present. Contributions to the knowledge of modeling flow and transport, as well as to the characterization of porous media at field scale are of great relevance. This book addresses several of these issues, treated with a variety of methodologies grouped into four parts: I Fundamental concepts II Flow and transport III Statistical and stochastic characterization IV Waves The problems analyzed in this book cover diverse length scales that range from small rock samples to field-size porous formations. They belong to the most active areas of research in porous media with applications in geosciences developed by diverse authors. This book was written for a broad audience with a prior and basic knowledge of porous media. The book is addressed to a wide readership, and it will be useful not only as an authoritative textbook for undergraduate and graduate students but also as a reference source for professionals including geoscientists, hydrogeologists, geophysicists, engineers, applied mathematicians and others working on porous media.
Download or read book SPE Reprint Series written by and published by . This book was released on 1985 with total page 486 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Energy Research Abstracts written by and published by . This book was released on 1992-10 with total page 508 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Journal of Energy Resources Technology written by and published by . This book was released on 1981 with total page 778 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Petroleum Abstracts Literature and Patents written by and published by . This book was released on 1990 with total page 1416 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Society of Petroleum Engineers Journal written by Society of Petroleum Engineers of AIME. and published by . This book was released on 1982 with total page 466 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Department of Energy Research and Development Programs fiscal Year 1984 written by United States. Congress. Senate. Committee on Energy and Natural Resources. Subcommittee on Energy Research and Development and published by . This book was released on 1983 with total page 908 pages. Available in PDF, EPUB and Kindle. Book excerpt:
