Download or read book An Introduction to Low Temperature Differential Stirling Engines written by James R. Senft and published by . This book was released on 1996 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stirling and Thermal Lag Engines Motive Power Without the Co2 written by Allan J. Organ and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Existing literature focuses on the alleged merits of the Stirling engine. These are indeed latent but, decades on, remain to be fully realised. This is despite the fact that Stirling and other closed-cycle prime-movers offer a contribution to an ultra-low carbon economy. By contrast with solar panels, the initial manufacture of Stirling engines makes no demands on scarce or exotic raw materials. Further, calculating embodied carbon per kWh favours the Stirling engine by a wide margin. However, the reader expecting to find the Stirling engine promoted as a panacea for energy problems may be surprised to find the reverse. Stirling and Thermal-Lag Engines reflects upon the fact that there is more to be gained by approaching its subject as a problem than as a solution. The Achilles heel of the Stirling engine is a low numerical value of specific work, defined as work per cycle per swept volume per unit of charge pressure and conventionally denoted Beale number NB. Measured values remain unimproved since 1818, quantified here for the first time at 2% of the NB of the modern internal combustion engine! The low figure is traced to incomplete utilisation of the working gas. Only a small percentage of the charge gas - if any - is processed through a complete cycle, i.e., between temperature extremes. The book offers ready-made tools including a simplified algorithm for particle trajectory map construction; an author-patented mechanism delivering optimised working-gas distribution; flow and heat transfer data re-acquired in context and an illustrated re-derivation of the academically respected Method of Characteristics which now copes with shock formation and flow-area discontinuities. All formulations are presented in sufficient detail to allow the reader to 'pick up and run' with them using the data offered in the book. The various strands are drawn together in a comprehensively engineered design of an internally focusing solar Stirling engine, presented in a form allowing a reader with access to basic machining facilities to construct one. The sun does not always shine. But neither will the oil always flow. This new title offers an entrée to technology appropriate to the 21st century.
Download or read book The Evolution of the Heat Engine written by Ivo Kolin and published by . This book was released on 1998-01-01 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Power Generation Technologies for Low Temperature and Distributed Heat written by Christos N. Markides and published by Woodhead Publishing. This book was released on 2023-06-13 with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power Generation Technologies for Low-Temperature and Distributed Heat presents a systematic and detailed analysis of a wide range of power generation systems for low-temperature (lower than 700-800°C) and distributed heat recovery applications. Each technology presented is reviewed by a well-known specialist to provide the reader with an accurate, insightful and up-to-date understanding of the latest research and knowledge in the field. Technologies are introduced before the fundamental concepts and theoretical technical and economic aspects are discussed, as well as the practical performance expectations. Cutting-edge technical progress, key applications, markets, as well as emerging and future trends are also provided, presenting a multifaceted and complete view of the most suitable technologies. A chapter on various options for thermal and electrical energy storage is also included with practical examples, making this a valuable resource for engineers, researchers, policymakers and engineering students in the fields of thermal energy, distributed power generation systems and renewable and clean energy technology systems. Presents a wide range of power generation technologies based on thermomechanical cycles, membrane technology, thermochemical, thermoelectric, photoelectric and electrochemical effects Explains the fundamental concepts and underlying operation principles in each case, and provides theoretical performance expectations and practical technical and economic characteristics Reviews the cutting-edge technical progress, key applications, markets, emerging and future trends, and includes practical examples of all technologies Details advantages and disadvantages of each technology to allow the reader to make informed decisions of their own for different applications
Download or read book Stirling Cycle Engine Analysis written by Israel Urieli and published by CRC Press. This book was released on 1984 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Free Piston Stirling Engines written by Graham Walker and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: DEFINITION AND NOMENCLATURE A Stirling engine is a mechanical device which operates on a closed regenerative thermodynamic cycle with cyclic compression and expansion of the working fluid at different temperature levels. The flow of working fluid is controlled only by the internal volume changes, there are no valves and, overall, there is a net conversion of heat to work or vice-versa. This generalized definition embraces a large family of machines with different functions; characteristics and configurations. It includes both rotary and reciprocating systems utilizing mechanisms of varying complexity. It covers machines capable of operating as a prime mover or power system converting heat supplied at high tempera ture to output work and waste heat at a lower temperature. It also covers work-consuming machines used as refrigerating systems and heat pumps abstracting heat from a low temperature source and delivering this plus the heat equivalent of the work consumed to a higher tem perature. Finally it covers work-consuming devices used as pressure generators compressing a fluid from a low pressure to a higher pres sure. Very similar machines exist which operate on an open regen erative cycle where the flow of working fluid is controlled by valves. For convenience these may be called Ericsson engines but unfortunate ly the distinction is not widely established and regenerative machines of both types are frequently called 'Stirling engines'.
Download or read book Stirling Engine Design Manual written by William Martini and published by CreateSpace. This book was released on 2013-01-25 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt: For Stirling engines to enjoy widespread application and acceptance, not only must the fundamental operation of such engines be widely understood, but the requisite analytic tools for the stimulation, design, evaluation and optimization of Stirling engine hardware must be readily available. The purpose of this design manual is to provide an introduction to Stirling cycle heat engines, to organize and identify the available Stirling engine literature, and to identify, organize, evaluate and, in so far as possible, compare non-proprietary Stirling engine design methodologies. This report was originally prepared for the National Aeronautics and Space Administration and the U. S. Department of Energy.
Download or read book Organic Rankine Cycle ORC Power Systems written by Ennio Macchi and published by Woodhead Publishing. This book was released on 2016-08-24 with total page 700 pages. Available in PDF, EPUB and Kindle. Book excerpt: Organic Rankine Cycle (ORC) Power Systems: Technologies and Applications provides a systematic and detailed description of organic Rankine cycle technologies and the way they are increasingly of interest for cost-effective sustainable energy generation. Popular applications include cogeneration from biomass and electricity generation from geothermal reservoirs and concentrating solar power installations, as well as waste heat recovery from gas turbines, internal combustion engines and medium- and low-temperature industrial processes. With hundreds of ORC power systems already in operation and the market growing at a fast pace, this is an active and engaging area of scientific research and technical development. The book is structured in three main parts: (i) Introduction to ORC Power Systems, Design and Optimization, (ii) ORC Plant Components, and (iii) Fields of Application. - Provides a thorough introduction to ORC power systems - Contains detailed chapters on ORC plant components - Includes a section focusing on ORC design and optimization - Reviews key applications of ORC technologies, including cogeneration from biomass, electricity generation from geothermal reservoirs and concentrating solar power installations, waste heat recovery from gas turbines, internal combustion engines and medium- and low-temperature industrial processes - Various chapters are authored by well-known specialists from Academia and ORC manufacturers
Download or read book Ringbom Stirling Engines written by James R. Senft and published by Oxford University Press, USA. This book was released on 1993 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Ringbom engine, an elegant simplification of the Stirling, is increasingly emerging as a viable, multipurpose engine. Despite its technical elegance, high-speed stable operation capabilities, and potential as an environment-friendly energy source, the advantages manifest in Ringbom design have been slowly realized, due in large to part to its often enigmatic operating regime. This book presents for the first time a clear, tractable mathematical model of the dynamic properties of the Ringbom, resulting in a theorem that offers a complete characterization of the stable operating mode of the engine. The author here details the research leading to the development of the Ringbom and illustrates theoretical results, engine characteristics, and design principles using data from actual Ringbom engines. Throughout the book, the author emphasizes an understanding of Ringbom engine properties through closed form mathematical analysis and lucidly details how his mathematical derivations apply to real engines. Extensive descriptions of the engine hardware are included to aid those interested in their construction. Mechanical, electrical, and chemical engineers concerned with power systems, power generation, energy conservation, solar energy, and low-temperature physics will find this monograph a comprehensive and technically rich introduction to Stirling Ringbom engine technology.
Download or read book Stirling Cycle Engines written by Allan J. Organ and published by John Wiley & Sons. This book was released on 2013-11-15 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt: Some 200 years after the original invention, internal design of a Stirling engine has come to be considered a specialist task, calling for extensive experience and for access to sophisticated computer modelling. The low parts-count of the type is negated by the complexity of the gas processes by which heat is converted to work. Design is perceived as problematic largely because those interactions are neither intuitively evident, nor capable of being made visible by laboratory experiment. There can be little doubt that the situation stands in the way of wider application of this elegant concept. Stirling Cycle Engines re-visits the design challenge, doing so in three stages. Firstly, unrealistic expectations are dispelled: chasing the Carnot efficiency is a guarantee of disappointment, since the Stirling engine has no such pretentions. Secondly, no matter how complex the gas processes, they embody a degree of intrinsic similarity from engine to engine. Suitably exploited, this means that a single computation serves for an infinite number of design conditions. Thirdly, guidelines resulting from the new approach are condensed to high-resolution design charts – nomograms. Appropriately designed, the Stirling engine promises high thermal efficiency, quiet operation and the ability to operate from a wide range of heat sources. Stirling Cycle Engines offers tools for expediting feasibility studies and for easing the task of designing for a novel application. Key features: Expectations are re-set to realistic goals. The formulation throughout highlights what the thermodynamic processes of different engines have in common rather than what distinguishes them. Design by scaling is extended, corroborated, reduced to the use of charts and fully Illustrated. Results of extensive computer modelling are condensed down to high-resolution Nomograms. Worked examples feature throughout. Prime movers (and coolers) operating on the Stirling cycle are of increasing interest to industry, the military (stealth submarines) and space agencies. Stirling Cycle Engines fills a gap in the technical literature and is a comprehensive manual for researchers and practitioners. In particular, it will support effort world-wide to exploit potential for such applications as small-scale CHP (combined heat and power), solar energy conversion and utilization of low-grade heat.
Download or read book Mechanical Efficiency of Heat Engines written by James R. Senft and published by Cambridge University Press. This book was released on 2007-08-13 with total page 135 pages. Available in PDF, EPUB and Kindle. Book excerpt: Publisher description
Download or read book Implicit Filtering written by C. T. Kelley and published by SIAM. This book was released on 2011-09-29 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: A description of the implicit filtering algorithm, its convergence theory and a new MATLAB® implementation.
Download or read book Natural Gas Engines written by Kalyan Kumar Srinivasan and published by Springer. This book was released on 2018-11-03 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the various advanced reciprocating combustion engine technologies that utilize natural gas and alternative fuels for transportation and power generation applications. It is divided into three major sections consisting of both fundamental and applied technologies to identify (but not limited to) clean, high-efficiency opportunities with natural gas fueling that have been developed through experimental protocols, numerical and high-performance computational simulations, and zero-dimensional, multizone combustion simulations. Particular emphasis is placed on statutes to monitor fine particulate emissions from tailpipe of engines operating on natural gas and alternative fuels.
Download or read book High Temperature Solid Oxide Fuel Cells for the 21st Century written by Kevin Kendall and published by Elsevier. This book was released on 2015-11-21 with total page 522 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-temperature Solid Oxide Fuel Cells, Second Edition, explores the growing interest in fuel cells as a sustainable source of energy. The text brings the topic of green energy front and center, illustrating the need for new books that provide comprehensive and practical information on specific types of fuel cells and their applications. This landmark volume on solid oxide fuel cells contains contributions from experts of international repute, and provides a single source of the latest knowledge on this topic. - A single source for all the latest information on solid oxide fuel cells and their applications - Illustrates the need for new, more comprehensive books and study on the topic - Explores the growing interest in fuel cells as viable, sustainable sources of energy
Download or read book Stirling Engines for Low temperature Solar thermal electric Power Generation written by Artin Der Minassians and published by . This book was released on 2007 with total page 418 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book 3D Printing and Additive Manufacturing written by Chee Kai Chua and published by World Scientific Publishing Company. This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Resource added for the Prototype and Design program 106142.
Download or read book The Philips Stirling Engine written by Clifford M. Hargreaves and published by Elsevier Science & Technology. This book was released on 1991 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is about the Stirling engine and its development from the heavy cast-iron machine of the nineteenth century into the efficient high-speed engine of today. It is not a handbook: it does not tell the reader how to build a Stirling engine. It is rather the history of a research effort spanning nearly fifty years, together with an outline of principles, some technical details and descriptions of the more important engines. No one will dispute the position of Philips as the pioneer of the modern Stirling engine. Hence the title of the book, hence also the contents, which are confined largely to the Philips work on the subject. Valuable work has been done elsewhere but this is discussed only marginally in order to keep the book within a reasonable size. The book is addressed to a wide audience on an academic level. The first two chapters can be read by the technically interested layman but after that some engineering background and elementary mathematics are generally necessary.Heat engines are traditionally the engineer's route to thermodynamics: in this context, the Stirling engine, which is the simplest of all heat engines, is more suited as a practical example than either the steam engine or the internal-combustion engine. The book is also addressed to historians of technology, from the viewpoint of the twentieth century revival of the Stirling engine as well as its nineteenth century origins.
