Download or read book A Handbook for Seismic Data Acquisition in Exploration written by Brian J. Evans and published by SEG Books. This book was released on 1997 with total page 319 pages. Available in PDF, EPUB and Kindle. Book excerpt: This illustration-rich book explains seismic data acquisition operations from a fundamental and practical standpoint, ranging from land to marine 2D methods to 3D seismic methods. Helpful to geologists, field crews, exploration managers, petroleum engineers, and geophysicists, each chapter concludes with exercises on field data recording problems.
Download or read book A Guide to Seismic Data Acquisition written by Rajendra Prasad and published by . This book was released on 2016-05-07 with total page 150 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with the optimization technique of seismic data acquisition parameter. Each aspect of acquisition parameter has been discussed in detail. Chapter-one deals with the general technique of seismic data acquisition and common meaning of some of the terms being used in exploration seismic in on land and offshore areas, particularly about characteristics of source & receiver and acquisition techniques. Chapter-two deals with the optimization of Geometrical Parameters i.e. far-offset distance, near-offset distance, group interval, effective array length, foldage, line orientation and line length. Chapter-three deals with the optimization of Source Parameters. Basic goal of optimization is to have required resolution and signal to noise ratio in the acquired data. For explosive source, shot hole depth, charge size and lithology of the medium surrounding the charge are three parameters which decide the source signature. First of all records with different depths below the weathering layer with equal charge size is taken. Signal to noise ratio and peak frequency of the signal at the main zone of interest is computed. Amplitude spectra of different traces at main zone of interest are also compared for all the records. Record giving highest peak frequency and signal to noise ratio corresponds to optimum depth. Now keeping this depth fixed, charge size is varied and record are taken. Again signal to noise ratio, peak frequency and amplitude spectra are compared and a suitable one is selected on the basis of frequency content and signal to noise ratio. In the case of land airgun, Number of airgun, number of pops and air gun patterns are the main parameters, which decide signal to noise ratio. In the case of Vibroseis, sweep length, end frequencies of the sweep and Vibroseis pattern are the main parameters to be optimized in the field. In marine work marine air gun is the widely used marine seismic source. Peak to peak amplitude, primary to bubble ratio (PBR) and bandwidth of the amplitude spectrum are the deciding parameters for selection of source.Chapter-four deals with the Source/Receiver Array Parameters. Effective array length, element's weighting and spacing are the parameters to be optimized on the basis of desired seismic resolution as well as degree of attenuation of coherent noise. Effectiveness of the array is examined by fold-back experiment and f-k diagram.Chapter-five deals with the Recording System & Quality Control. Silent features have been discussed here, which are essential to be adhered in the field so that objective of the survey is achieved.
Download or read book Simultaneous Source Seismic Acquisition written by Ray Abma and published by SEG Books. This book was released on 2020-12-31 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces simultaneous source technology and helps those who practice it succeed. Although the book does not include all developments, which would have entailed a much longer treatise, this work is written through the lens of decades of experiences and allows readers to understand the development of independent simultaneous sourcing. The relationships between data acquisition and data processing are discussed because never before have they been so intertwined as in this area. In addition to describing the underlying technologies, this book also is a user-guide which discusses survey design and acquisition and decribes the sensitivities of the processing algorithms which can allow simultaneous source technology to succeed. The audience for this book includes acquisition and processing geophysicists who will work with these data as well as those who require only an overview of the state of the art; and, even though they may not need the full technical details, they may want to know the limitations and advantages of using simultaneous sources.
Download or read book Land Seismic Case Studies for Near Surface Modeling and Subsurface Imaging written by Öz Yilmaz and published by SEG Books. This book was released on 2021-06-30 with total page 1056 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written for practicing geophysicists, “Land Seismic Case Studies for Near-Surface Modeling and Subsurface Imaging” is a comprehensive guide to understanding and interpreting seismic data. The culmination of land seismic data acquisition and processing projects conducted by the author over the last two decades, this book contains more than nearly 800 figures from worldwide case studies—conducted in both 2D and 3D. Beginning with Chapter 1 on seismic characterization of the near-surface, Chapter 2 presents near-surface modeling by traveltime and full-wave inversion, Chapter 3 presents near-surface modeling by imaging, and then Chapter 4 includes detailed case studies for near-surface modeling. Chapter 5 reviews single- and multichannel signal processing of land seismic data with the key objective of removing surface waves and guided waves that are characterized as coherent linear noise. Uncommon seismic data acquisition methods, including large-offset acquisition in thrust belts to capture the large-amplitude supercritical reflections, swath-line acquisition, and joint PP and SH- SH seismic imaging are highlighted in Chapter 6, and Chapter 7 presents image-based rms velocity estimation and discusses the problem of velocity uncertainty. The final two chapters focus exclusively on case studies: 2D in Chapter 8 and 3D in Chapter 9. An outstanding teaching tool, this book includes analysis workflows containing processing steps designed to solve specific problems. Essential for anyone involved in acquisition, processing, and inversion of seismic data, this volume will become the definitive reference for understanding how the variables in seismic acquisition are directly reflected in the data.
Download or read book A GUIDE BOOK SUB SURFACE DATA MANAGEMENT FOR DATA MANAGERS OIL GAS SECTOR VOLUME 1 SEISMIC written by Ahmad Maidinsar and published by Xlibris Corporation. This book was released on 2014-08-21 with total page 283 pages. Available in PDF, EPUB and Kindle. Book excerpt: As the oil and gas (O&G) industry grows by leaps and bounds, so do data; kb (kilobyte) -> Yb (Yottabyte). This book is specifically written for O&G Data Management personnel and Earth Sciences majoring students who will juggle and grapple with seismic data on a routine basis during the course of their career or study. The step by step methodology, though seems orthodox, has been revisited so as to ensure no unnecessary repetition of work. The book will pave the way for O&G Data Management personnel to have a firm grip in handling seismic data entrusted to them, and to deal with the data in a professional way with no "cutting corners". It must be noted that when dealing with seismic data management, the word "novice" is not in the work vocabulary. Throughout this book, O&G Data Management personnel get to understand the basics of the seismic data and their management, and acquire additional skill that can be applied to any sub-surface data management with minimal changes to the workflow Yottabyte — The biggest storage capacity defined by Julian Bunn ET el in the GIOD project
Download or read book Seismic Data Interpretation and Evaluation for Hydrocarbon Exploration and Production written by Niranjan C. Nanda and published by Springer. This book was released on 2016-03-10 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces readers to the field of seismic data interpretation and evaluation, covering themes such as petroleum exploration and high resolution seismic data. It helps geoscientists and engineers who are practitioners in this area to both understand and to avoid the potential pitfalls of interpreting and evaluating such data, especially the over-reliance on sophisticated software packages and workstations alongside a lack of grasp on the elementary principles of geology and geophysics. Chapters elaborate on the necessary principles, from topics like seismic wave propagation and rock-fluid parameters to seismic modeling and inversions, explaining the need to understand geological implications. The difference between interpretation of data and its evaluation is highlighted and the author encourages imaginative, logical and practical application of knowledge. Readers will appreciate the exquisite illustrations included with the accessibly written text, which simplify the process of learning about interpretation of seismic data. This multidisciplinary, integrated and practical approach to data evaluation will prove to be a valuable tool for students and young professionals, especially those connected with oil companies.
Download or read book Acquisition and Processing of Marine Seismic Data written by Derman Dondurur and published by Elsevier. This book was released on 2018-03-09 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: Acquisition and Processing of Marine Seismic Data demonstrates the main principles, required equipment, and suitable selection of parameters in 2D/3D marine seismic data acquisition, as well as theoretical principles of 2D marine seismic data processing and their practical implications. Featuring detailed datasets and examples, the book helps to relate theoretical background to real seismic data. This reference also contains important QC analysis methods and results both for data acquisition and marine seismic data processing. Acquisition and Processing of Marine Seismic Data is a valuable tool for researchers and students in geophysics, marine seismics, and seismic data, as well as for oil and gas exploration. Contains simple step-by-step diagrams of the methodology used in the processing of seismic data to demonstrate the theory behind the applications Combines theory and practice, including extensive noise, QC, and velocity analyses, as well as examples for beginners in the seismic operations market Includes simple illustrations to provide to the audience an easy understanding of the theoretical background Contains enhanced field data examples and applications
Download or read book Practical Applications of Time lapse Seismic Data written by David H. Johnston and published by SEG Books. This book was released on 2013 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: Time-lapse (4D) seismic technology is a key enabler for improved hydrocarbon recovery and more cost-effective field operations. This book shows how 4D data are used for reservoir surveillance, add value to reservoir management, and provide valuable insight on dynamic reservoir properties such as fluid saturation, pressure, and temperature.
Download or read book 3D Seismic Survey Design written by Gijs J. O. Vermeer and published by SEG Books. This book was released on 2012 with total page 369 pages. Available in PDF, EPUB and Kindle. Book excerpt: Details the properties of 3D acquisition geometries and shows how they naturally lead to the 3D symmetric sampling approach to 3D survey design. Many examples are used to illustrate choices of acquisition parameters, and the link between survey parameters and noise suppression as well as imaging is an intrinsic part of the contents.
Download or read book Simultaneous Source Seismic Acquisition written by Ray Abma and published by . This book was released on 2020 with total page 205 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces simultaneous source technology and helps those who practice it succeed. Although the book does not include all developments, which would have entailed a much longer treatise, this work is written through the lens of decades of experiences and allows readers to understand the development of independent simultaneous sourcing. The relationships between data acquisition and data processing are discussed, because never before have they been so intertwined as in this area. In addition to describing the underlying technologies, this book also is a user-guide which discusses survey design and acquisition and describes the sensitivities of the processing algorithms which can allow simultaneous source technology to succeed. The audience for this book includes acquisition and processing geophysicists who will work with these data as well as those who require only an overview of the state of the art; and, even though they may not need the full technical details, they may want to know the limitations and advantages of using simultaneous sources.
Download or read book XDETECT written by D. M. Tottingham and published by . This book was released on 1989 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Introduction to Petroleum Seismology second edition written by Luc T. Ikelle and published by SEG Books. This book was released on 2018-03-26 with total page 1403 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to Petroleum Seismology, second edition (SEG Investigations in Geophysics Series No. 12) provides the theoretical and practical foundation for tackling present and future challenges of petroleum seismology especially those related to seismic survey designs, seismic data acquisition, seismic and EM modeling, seismic imaging, microseismicity, and reservoir characterization and monitoring. All of the chapters from the first edition have been improved and/or expanded. In addition, twelve new chapters have been added. These new chapters expand topics which were only alluded to in the first edition: sparsity representation, sparsity and nonlinear optimization, near-simultaneous multiple-shooting acquisition and processing, nonuniform wavefield sampling, automated modeling, elastic-electromagnetic mathematical equivalences, and microseismicity in the context of hydraulic fracturing. Another major modification in this edition is that each chapter contains analytical problems as well as computational problems. These problems include MatLab codes, which may help readers improve their understanding of and intuition about these materials. The comprehensiveness of this book makes it a suitable text for undergraduate and graduate courses that target geophysicists and engineers as well as a guide and reference work for researchers and professionals in academia and in the petroleum industry.
Download or read book Survey Design and Seismic Acquisition for Land Marine and In between in Light of New Technology and Techniques written by David J. Monk and published by SEG Books. This book was released on 2020-02-03 with total page 215 pages. Available in PDF, EPUB and Kindle. Book excerpt: Seismic surveys are subject to many different design criteria, but often the parameters are established based on an outdated view of how data can be acquired and how it will be processed. This book highlights what is possible using modern acquisition methods, techniques, and equipment, and how these may impact seismic survey design and acquisition.
Download or read book Seismic Imaging a Practical Approach written by Jean-Luc Mari and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the geophysics of oil exploration and reservoir studies, the surface seismic method is the most commonly used method to obtain a subsurface model in 2 or 3 dimensions. This method plays an increasingly important role in soil investigations for geotechnical, hydrogeological and site characterization studies regarding seismic hazard issues. The goal of this book is to provide a practical guide, using examples from the field, to the application of seismic methods to surface imaging. After reviewing the current state of knowledge in seismic wave propagation, refraction and reflection seismic methods, the book aims to describe how seismic tomography and fullwave form inversion methods can be used to obtain seismic images of the subsurface. Through various synthetic and field examples, the book highlights the benefit of combining different sets of data: refracted waves with reflected waves, and body waves with surface waves. With field data targeting shallow structures, it shows how more accurate geophysical models can be obtained by using the proposed hybrid methods. Finally, it shows how the integration of seismic data (3D survey and VSP), logging data (acoustic logging) and core measurements, combined with a succession of specific and advanced processing techniques, enables the development of a 3D high resolution geological model in depth. In addition to these examples, the authors provide readers with guidelines to carry out these operations, in terms of acquisition, as well as processing and interpretation. In each chapter, the reader will find theoretical concepts, practical rules and, above all, actual application examples. For this reason, the book can be used as a text to accompany course lectures or continuing education seminars. This book aims to promote the exchange of information among geologists, geophysicists, and engineers in geotechnical fields.
Download or read book Exploration Seismology written by R. E. Sheriff and published by Cambridge University Press. This book was released on 1995-08-25 with total page 1261 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the completely updated revision of the highly regarded book Exploration Seismology. Available now in one volume, this textbook provides a complete and systematic discussion of exploration seismology. The first part of the book looks at the history of exploration seismology and the theory - developed from the first principles of physics. All aspects of seismic acquisition are then described. The second part of the book goes on to discuss data-processing and interpretation. Applications of seismic exploration to groundwater, environmental and reservoir geophysics are also included. The book is designed to give a comprehensive up-to-date picture of the applications of seismology. Exploration Seismology's comprehensiveness makes it suitable as a text for undergraduate courses for geologists, geophysicists and engineers, as well as a guide and reference work for practising professionals.
Download or read book 3 D Seismic Interpretation written by M. Bacon and published by Cambridge University Press. This book was released on 2007-10-18 with total page 236 pages. Available in PDF, EPUB and Kindle. Book excerpt: 3-D seismic data have become the key tool used in the petroleum industry to understand the subsurface. In addition to providing excellent structural images, the dense sampling of a 3-D survey makes it possible to map reservoir quality and the distribution of oil and gas. Topics covered in this book include basic structural interpretation and map-making; the use of 3-D visualisation methods; interpretation of seismic amplitudes, including their relation to rock and fluid properties; and the generation and use of AVO and acoustic impedance datasets. This new paperback edition includes an extra appendix presenting new material on novel acquisition design, pore pressure prediction from seismic velocity, elastic impedance inversion, and time lapse seismics. Written by professional geophysicists with many years' experience in the oil industry, the book is indispensable for geoscientists using 3-D seismic data, including graduate students and new entrants into the petroleum industry.
Download or read book Handbook of Poststack Seismic Attributes written by Arthur E. Barnes and published by SEG Books. This book was released on 2016-10-15 with total page 269 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Handbook of Poststack Seismic Attributes is a general reference for poststack seismic attributes. It discusses their theory, meaning, computation, and application, with the goal of improving understanding so that seismic attributes can be applied more effectively. The chapters of the book build upon each other and progress from basic attributes to more involved methods. The book introduces the ideas that underlie seismic attributes and reviews their history from their origins to current developments. It examines attribute maps and interval statistics; complex trace attributes; 3D attributes that quantify aspects of geologic structure and stratigraphy, primarily dip, azimuth, curvature, reflection spacing, and parallelism; seismic discontinuity attributes derived through variances or differences; spectral decomposition, thin-bed analysis, and waveform classification; the two poststack methods that purportedly record rock properties — relative acoustic impedance through recursive inversion, and Q estimation through spectral ratioing; and multiattribute analysis through volume blending, cross-plotting, principal component analysis, and unsupervised classification. The book ends with an overview of how seismic attributes aid data interpretation and discusses bright spots, frequency shadows, faults, channels, diapirs, and data reconnaissance. A glossary provides definitions of seismic attributes and methods, and appendices provide background mathematics. The book is intended for reflection seismologists engaged in petroleum exploration, including seismic data interpreters, data processors, researchers, and students.
