Download or read book A Course in Elementary Mechanical Drawing Classic Reprint written by Wm; A. Pike and published by . This book was released on 2015-08-04 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from A Course in Elementary Mechanical Drawing Each Student will require the following Instruments on beginning the course, viz.: - Half-a-dozen Sheets of Drawing Paper, a Drawing-board, a T-square, a Pair of Triangles, a Hard Pencil, a Right Line Pen, a Pair of Compasses with Pen, Pencil and Needle Points, a Pair of Plain Dividers, an accurate and finely divided Scale, a piece of India Ink, a Rubber, an Irregular Curve, and half-a-dozen Thumb-tacks. These instruments and materials are all that are absolutely required up to the time of commencing tinting and shading, when a few other articles will be needed, which will be spoken of in their proper place. Before purchasing, the following directions about the different instruments and materials should be noticed. Paper. For all the drawings of this course, use Whatman's Imperial drawing paper. It comes in sheets of convenient size, and is well adapted to the work of the course. Six sheets will be enough up to the time of tinting. Drawing-Board. Great care should be taken to secure a good drawing-board. The best boards are those made of thoroughly seasoned white pine, one inch thick, with cleats at the ends flush with the surface of the board. The most convenient size is twenty-three by thirty-one inches. This gives a small margin outside of a whole sheet of Imperial paper, which is twenty-two by thirty-inches. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book Notes on Elementary Mechanical Drawing written by H. J. Goulding and published by Forgotten Books. This book was released on 2016-09-02 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Notes on Elementary Mechanical Drawing: Course 1; University of Michigan, 1905 In the. Construction of the following problems familiarity with the instruments and accuracy in execution are the chief objects to be attained. Before commencing any drawing the student should see that his instruments are in working order. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book A Text Book of Mechanical Drawing and Elementary Machine Design Classic Reprint written by John S. Reid and published by Forgotten Books. This book was released on 2017-10-28 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from A Text-Book of Mechanical Drawing and Elementary Machine Design To properly prepare students for advanced machine design it has been found necessary to introduce a course designed to apply the principles of mechanical drawing to the solution of practical problems in machine construction and to familiarize the student with the arrangement and proportions of the most important machines and their details recognized by competent engineers to be the best practice of the present time. It is essential to intelligent study and an economical expenditure of time and labor that, before attempting to design a new machine or improve an old one, the student should post himself with all possible information concerning what has already been done in the same direction. To this end the present work has been prepared. In it we have attempted to show what is the best United States practice in the design and construction of various machines and details of machines, using rules and formulae whenever feasible in working out practical problems. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book A Course in Elementary Mechanical Drawing written by and published by . This book was released on 1891 with total page 43 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Elementary Mechanical Drawing written by Frank Aborn and published by Forgotten Books. This book was released on 2016-10-20 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Elementary Mechanical Drawing: For School and Shop In my endeavors to develop in the minds of pupils in grammar and high school classes a clear comprehension of the elementary principles of me chanical drawing, it was found that something more was needed than the copying of a few isolated problems into drawing-books. The student gained a better grasp of this subject by solving a limited number of written problems, illustrating a principle or method of mechanical drawing that had been previously explained by the teacher from the black board. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book A Course in Mechanical Drawing Classic Reprint written by John S. Reid and published by Forgotten Books. This book was released on 2017-10-24 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from A Course in Mechanical Drawing A need has been felt by instructors and students, especially in technical courses, for a text-book that would illustrate the fundamental principles Of mechanical drawing in such a prac tical, lucid, direct and progressive way as to enable the instructor to teach, and the student to acquire, the greatest number of the essential principles involved, and the ability to apply them, in a draftsman-like manner, in the shortest space of time. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book TEXT BOOK OF MECHANICAL DRAWING AND ELEMENTARY MACHINE DESIGN LARGE TEXT CLASSIC REPRINT written by JOHN S. REID and published by . This book was released on 2018 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Intermediate Course in Mechanical Drawing written by William Henry Thorne and published by . This book was released on 1891 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanical Drawing written by John S. Reid and published by Forgotten Books. This book was released on 2015-07 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Mechanical Drawing: Elementary and Advanced A mechanical drawing is used to convey precise information from one person to another. A patternmaker must have a true drawing of an object, giving correct dimensions and instructions before he can make a pattern, from which the foundryman can make a rough casting. The machinist must have a drawing from which he can obtain accurate information to enable him to take the rough casting and by slotting, planing, drilling, grinding, chipping or turning he can produce the finished article as designed by the draftsman. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book Mechanical Drawing Working Drawings Classic Reprint written by Arthur B. Babbitt and published by Forgotten Books. This book was released on 2018-03-21 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Mechanical Drawing Working Drawings The course maybe given without home-work, but the author is a firm believer in home - work. Where such work is required, the results immediately aimed at are better, and in many indirect ways the subject is found to have a higher educational value. The author has, therefore, been rather liberal in sugges tions for outside work, and has added extra plates for the special benefit of the ambitious student. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book Shop Sketching written by Ralph F. Windoes and published by Forgotten Books. This book was released on 2016-08-26 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Shop Sketching: A Course of Problems for Mechanical Drawing Students As stated before, all of the problems in this-course will be made as freehand orthographic or perspective sketches. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book COURSE IN ELEM MECHANICAL DRAW written by William A. Pike and published by Wentworth Press. This book was released on 2016-08-25 with total page 78 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work has been selected by scholars as being culturally important, and is part of the knowledge base of civilization as we know it. This work was reproduced from the original artifact, and remains as true to the original work as possible. Therefore, you will see the original copyright references, library stamps (as most of these works have been housed in our most important libraries around the world), and other notations in the work. This work is in the public domain in the United States of America, and possibly other nations. Within the United States, you may freely copy and distribute this work, as no entity (individual or corporate) has a copyright on the body of the work. As a reproduction of a historical artifact, this work may contain missing or blurred pages, poor pictures, errant marks, etc. Scholars believe, and we concur, that this work is important enough to be preserved, reproduced, and made generally available to the public. We appreciate your support of the preservation process, and thank you for being an important part of keeping this knowledge alive and relevant.
Download or read book A Practical Course in Mechanical Drawing Classic Reprint written by William Fox and published by . This book was released on 2017-01-20 with total page 138 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Junior Course in Mechanical Drawing Classic Reprint written by William H. Thorne and published by Forgotten Books. This book was released on 2018-02-03 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Junior Course in Mechanical Drawing Entered according to Act of Congress, in the year 1888, by william H. Thorne, In the office of the Librarian of Congress, at Washington. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book A Course in Mechanical Drawing for Evening Schools and Self Instruction Classic Reprint written by Louis Rouillion and published by Forgotten Books. This book was released on 2017-11-20 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from A Course in Mechanical Drawing for Evening Schools and Self-Instruction This course in Mechanical Drawing is the result of a number of years' work with even ing classes, and has been evolved from a careful study of the needs of such classes. The course was originally issued in blue print form, with accompanying typewritten notes. In this form it has been in use at the Pratt Institute and other schools, and in Y. M. C. A. Classes, for the past four years. In a modified form it has appeared serially in The entire course has been carefully revised, and is now published in the more convenient form of a text-book. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book Elementary Mechanical Drawing written by Charles William Weick and published by Forgotten Books. This book was released on 2018-02-04 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Elementary Mechanical Drawing: Theory and Practice Mechanical drawing is the art Of exact drawing by means Of drawing instruments Of precision. It differs from free-hand draw ing because it uses instruments and in general aims to reproduce the Object not as it appears to the eye in perspective but in its absolute relations in space. Mechanical Drawing is a generic title; specialized branches Of mechanical drawing are known as architectural drawing, topographical drawing, machine design, etc. The elements which underlie or are involved in the art Of mechanical drawing are: First, The Theory Of Projection; Second, Geometrical Drawing, and Third, Mathematics. The principles Of projection are involved, since we aim to transfer Objects having three dimensions to one plane Of two dimensions (the drawing paper). The difficulty which usually attends the study Of projection will be greatly lessened if a good method Of instruction is followed. It is better, for instance, to begin with simple Objects, than with complex ones. It is better to study minutely each separate detail, rather than several parts at once; studies Of unit details can then be built up to cover the whole Of a complex Object. The student, moreover, Should not be content with one study Of the Object but should make several studies Of the same Object in different positions. He should early acquire the habit Of analyzing, from the draftsman's point Of view, every Object into its parts and details. This power Of analysis once acquired saves time, ensures correctness, and is the secret Of power in the handling Of difficult and unusual problems. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Download or read book Intermediate Course in Mechanical Drawing Classic Reprint written by William Henry Thorne and published by Forgotten Books. This book was released on 2016-09-07 with total page 70 pages. Available in PDF, EPUB and Kindle. Book excerpt: Excerpt from Intermediate Course in Mechanical Drawing The dimension lines and all imaginary lines, or those which do not repre sent parts of the object itself, but serve as bases or lines of reference, or which are necessarily used in the construction of the drawing and the preservation of which would be desirable, should be distinguished from the black lines of the object in such manner as not to interfere nith the clearness of the latter. In other words, the object should stand out boldly and clearly to permit a ready general comprehension of it, while the detailed information concerning it should be kept somewhat in the background. The importance of this is not so appar ent in the drawing of the simple geometrical solids in the following problems, but it is very great in all work of any intricacy. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
